manualshive.com logo in svg

Mark MEGAFLEX, Техническое руководство

Поделиться
Скачать
Mark MEGAFLEX Скачать руководство пользователя страница 2

2

INSTRUCTIONS FOR USER

If you have questions concerning the use of your boiler or heating system, please ask your installer. It is in 

your own interest and that of the installer that you are aware of how to operate your boiler and heating 

system safely and efficiently.

The appliance is not to be used by children or persons with reduced physical, sensory or mental 

capabilities, or lack of experience and knowledge.

Children, even if being supervised, must not play with the appliance

In the case of failure or malfunction of the appliance, do not attempt to repair it yourself. 

Please contact your installer. Repairs must only be carried out by qualified technicians. Failure to 

comply with these requirements can compromise the safety of the appliance.

Operation

Water, coming from the radiators or from the DHW unit is heated in the aluminium heat exchanger. The 

CH or DHW pump guarantees circulation of water. The air needed for combustion is sucked in by a rpm 

controlled fan. At low boiler temperatures the flue gases can be cooled sufficiently for condensation of 

the water. This water is drained to the sewer via a built in syphon. This drainage must never be blocked. A 
burner controller with built in micro processor provides the electrical control of the boiler.

Topping up

The built in manometer indicates if the waterpressure is sufficient. As soon as the water pressure drops 

below 1 bar topping up is necessary. If topping up becomes a regular ocurrance, your installation should 

be checked by an installer.

Disconnect from the main. Connect the filling hose to the cold water tap and to the fill and drain valve 
of the boiler. Before tightning the coupling in the installation slowly fill the hose with water allowing any 
air present to escape. Open the fill and drain valve and slowly fill the installation until a pressure between 
1.5 and 2.0 bar is reached. When finished connect again to the main.

Bleeding

To remove any air present in the heating system and boiler, bleeding is necessary. Disconnect from the 
main. Open all the radiator valves. Bleed the air from all the radiators starting with the ones at the 
lowest point in the system. After bleeding, check the water pressure and top-up if required (if water 

pressure has dropped below 1 bar). Connect to the main again.

Starting the boiler

Please ask your installer how to start the boiler. Depending on how your heating system is controlled, 

this could be via an external timeclock, thermostat, switch or otherwise. Once the boiler volt-free enable 
contacts are closed, the boiler will commence its starting sequence.

Boiler flow temperature

The burner controller can adjust the flow temperature between 20 ° and 85 °C. The temperature setting 

can be changed using the control panel.

The installation manual provides the instructions for setting the flow temperature.

DHW (Hot Water) temperature ( if applicable)

From the factory, the DHW temperature is set to a value of 60 °C. This set value can be changed to any 

value between 35 and 65 °C using the buttons on the control panel. If the DHW device has a thermostat 

the DHW temperature can be adjusted by setting this thermostat.

Содержание MEGAFLEX



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды