Marine Power S62M42C Скачать руководство пользователя | Manualshive

Страница: 35 / 44

background image

33

www.MarinePowerUSA.com

12.

Trouble Shooting

Excessive Oil Consumption

Possible Cause

Remedy

External Leak

Clean/Check/Repair

Excessive Oil in Crankcase

Remove Excess Oil. Refer to Engine Identification on Page 15 for Correct Oil Level

Oil/Fuel Dilution

Change Oil

Extended Excessive RPM’s

Reduce RPM’s

Incorrect Oil Viscosity

Change to Proper Oil

Engine Vents Blocked

Unblock Vents

Defective Piston Rings

See Dealer

Defective Cylinders

See Dealer

Excessive Bearing Clearance

See Dealer

The Amount of Oil Used is Greatly Dependent Upon Engine Speed. Oil Usage Will be Greater at Higher RPM’s.

Water in Engine Cylinder or Base

Possible Cause

Remedy

Operator Error

See Section 7: Precautions on Page 23. REMOVE Water from Engine Immediately

Cylinder Head Gasket Leak

Contact Dealer. REMOVE Water from Engine Immediately

Cracked Block or Cylinder Head

Contact Dealer. REMOVE Water from Engine Immediately

Intake Manifold Gasket

Contact Dealer. REMOVE Water from Engine Immediately

Remove water by removing spark plugs and turning the engine over by hand. Once water is removed spray cylinder with Marvel Mystery Oil or 2-Cycle Engine
Oil. Drain all the oil and change the oil filter(s). Again, turn the engine over by hand to circulate the oil. Contact your dealer immediately to make the required
repairs. Upon completion of repairs, run the engine and again change the oil.

«
...
33
34
35
36
37
...
»

Содержание S62M42C













































Отзывы:

Нет отзывов

Похожие инструкции для S62M42C

Бренд: Stihl Страницы: 40

Бренд: YuanDong Страницы: 23

MAX-61SX-H RING WC Series

Бренд: O.S. engine Страницы: 36

Бренд: E-Z-GO Страницы: 112

1550 STERNDRIVE

Бренд: Mercury Racing Страницы: 75

Бренд: SCREENLINE Страницы: 4

Бренд: Yamaha Страницы: 51

Бренд: Nice Страницы: 21

Era-Era Zero E LH

Бренд: Nice Страницы: 32

Бренд: Volvo Penta Страницы: 94

Бренд: Robin America Страницы: 78

Бренд: HIOTH TECHNOLOGY Страницы: 5

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды