Marine Power S62M42C страница 11 Скачать руководство пользователя | Manualshive

Страница: 11 / 44

background image

9

www.MarinePowerUSA.com

4.

Electronic Sequential Fuel Injection Information

The engines covered in this manual are equipped with
Electronic Sequential Fuel Injection. The main fuel
system components include:

•  The electric high and low pressure fuel pumps
•  The throttle body assembly
•  The fuel injectors

The fuel injection system is controlled by an Electronic
Control Module (ECM). The ECM continually monitors
information from the various sensors on the engine and
configures the spark timing and fuel delivery for optimum
performance. Additionally, the ECM protects the engine
from over-revving and monitors the oil pressure and water
temperature.

The following sensors constantly provide information to
the ECM.

•  Engine Coolant Temperature (ECT) Sensor
•  Engine Oil Pressure Sensor
•  Manifold Absolute Pressure (MAP) Sensor
•  Knock Sensor
•  Camshaft Positioning (CMP) Sensor
•  Crankshaft Positioning (CKP) Sensor
•  Intake Air Temperature (IAT) Sensor (combined

with the MAP sensor on the 5.7)

•  Throttle Position (TPS) Sensor
•  Pedal Position (PPS) Sensor
•  Pre-Catalyst O2 (O2) Sensor (Catalyst equipped

engines)

• Post-Catalyst O2 (O2) Sensor (Catalyst equipped

engines)

Engines may include one or more of the following
optional sensors.

•  Engine Oil Temperature Sensor
•  Fuel Pressure Sensor
•  Transmission Oil Temperature Sensor
•  Exhaust Manifold Temperature Sensor

• Barometric Pressure (BARO) Sensor
• Super Charger Inlet Pressure (SCIP) Sensor

«
...
9
10
11
12
13
...
»

Содержание S62M42C













































Отзывы:

Нет отзывов

Похожие инструкции для S62M42C

Бренд: Wacker Neuson Страницы: 44

Бренд: Rato Страницы: 65

Бренд: Paccar Страницы: 71

Бренд: ACM Страницы: 36

Air Cooled TR-10D

Бренд: Wisconsin Страницы: 46

Бренд: Farymann Diesel Страницы: 76

Бренд: RHINO Страницы: 20

Walker Ford / Lehman

Бренд: AirSep Страницы: 4

Бренд: ebm-papst Страницы: 9

Бренд: O.S. engine Страницы: 4

Бренд: Lister Petter Страницы: 81

Бренд: Lister Petter Страницы: 100

Бренд: Volvo Penta Страницы: 8

Бренд: Volvo Penta Страницы: 20

Бренд: CW Products Страницы: 4

Бренд: YS Страницы: 2

Бренд: Sisu Diesel Страницы: 116

Бренд: Honda Страницы: 69

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды