Marathon Electric DVR 2000E+ Скачать руководство пользователя страница 54

Страница: 54 / 72

IDENTIFICATION TAB (7)

This panel contains non-editable fields for the DVR

serial number, software version, settings version and

MODBUS address. It also contains editable fields

for custom tags.

DVRPortal

™

Graphical User Interface (GUI)

•

Serial Number

is the serial number of the

DVR

•

Software Version

is the version of DVR

firmware.

•

Settings Version

is the version of factory

default settings for the DVR

•

MODBUS Address

is the MODBUS address

of the DVR

. Currently this is not editable

and has a default value of 1.

•

Customer Tag 1

is a 15-character string that

can be stored to the DVR

. The Write Tags

button will write the string into the DVR

RAM, but a Save to EEPROM is needed to

store the tag in the non-volatile memory.

•

Customer Tag 2

is a 15-character string that

can be stored to the DVR

Note:

The Write Tags button will write the string into

the DVR

RAM, but a Save to EEPROM is needed to

store the tag in the non-volatile memory.

GPN046 04-13.indd 52

4/5/13 10:24 AM

Содержание DVR 2000E+









































































Результаты поиска

Содержание DVR 2000E+

Отзывы:

Бренды по названию

Популярные бренды

Marathon Electric DVR 2000E+, Руководство пользователя

Результаты поиска

Содержание DVR 2000E+

Отзывы:

Бренды по названию

Популярные бренды