Marathon Electric DVR 2000E+ Скачать руководство пользователя страница 12

10

4

Fault Output Contact

A fault output contact is provided through terminals 

J1-6  and  J1-7.  This  normally-open,  form-A  contact 

closes in the event of a protective shutdown. 

DVR

®

 OPERATING FEATURES

Regulation Modes

The DVR

®

2000E+ provides three modes of regulation 

selectable through the HMI or through DVRPortal™. 

The DV adds two more regulation modes.

Automatic Voltage Regulation Modes

There are two automatic voltage regulation modes.  

AVR1 should be selected if the regulator is con-

nected for single phase voltage sensing and AVR3 

should be selected if the regulator is connected for 

three phase voltage sensing.  In either mode, the 

DVR

®

 regulates the RMS generator output voltage. 

Regulation is accomplished by sensing generator 

output  voltage  and  adjusting  dc  output  excitation 

current to maintain voltage at the regulation set 

point. The regulation set point is adjusted via the UP 

and DOWN contact inputs, the auxiliary input (when 

enabled), the HMI or DVRPortal™.  The Droop and 

Under Frequency functions may influence the regu

-

lation set point.

Field Current Regulation Mode

In FCR mode, the DVR

®

 maintains DC excitation 

current at a commanded level.  The regulation set 

point  is  adjusted  via  the  UP  and  DOWN  contact 

inputs, the auxiliary input (when enabled), the HMI or 

DVRPortal™. 

Reactive Power Regulation Mode (EC+ only)

In Reactive Power Regulation (VAR) mode, the DVR

®

 

maintains the generator’s reactive power at a com-

manded level.  The regulation set point is adjusted 

via the UP and DOWN contact inputs, the auxiliary 

input (when enabled), the HMI or DVRPortal™. This 

mode  can  only  be  entered  by  selecting  “VAR”  as 

the  regulation  mode  and  opening  the  VAR/PF_OFF 

contact input.

Power Factor Regulation Mode (EC+ Only)

In Power Factor Regulation (PF) mode, the DVR

®

 

maintains the generator’s power factor at a com-

manded level.  The regulation set point is adjusted 

via the UP and DOWN contact inputs, the auxiliary 

input (when enabled), the HMI or DVRPortal™. This 

mode can only be entered by selecting “PF” as the 

regulation mode 

and

 opening the VAR/PF_OFF con

-

tact input.

Auxiliary Input

 

NOTE:

  

If the DC voltage is removed from the aux-

iliary input, the operating set point will no longer 

be modified and the regulator will regulate to the 

programmed regulation set point.

Functionality of the auxiliary input is dependent on 

the configuration of the modes described below.  The 

auxiliary input can be set to Off, Control1, Control2 

or Meter modes through the HMI or DVRPortal™.  

The effect of the auxiliary input on the set point is 

displayed in DVRPortal™.

Auxiliary – Off

In this mode, any signal applied to the auxiliary input 

will be displayed in DVRPortal™, but will have no 

effect on the set point of the regulator.  

Auxiliary – Control1

This mode allows modification of the regulation set 

point by the application of a positive or negative DC 

voltage  across  terminals  J1-1  (+)  and  J1-12  (-).    A 

voltage up to +/- 3 Vdc may be applied at this input.  

When in AVR3 or AVR1:

The  application  of  a  +/-  3.000  Vdc  signal  corre

-

sponds to a percentage offset of up to +/- 30.0% to 

the set point.  

Example:

 A programmed regulation set point of 480 

Vrms, with an auxiliary input scale factor of 30% and 

an auxiliary input of -1 Vdc will result in a –48 Vrms 

offset to the set point.  Therefore the regulator will 

regulate to a reference voltage of 432 Vrms.

When in FCR:

The application of a +/- 3.000 Vdc signal corresponds 

to a -3.000 to3.000 Adc field current set point.  The 

auxiliary input scale factor is disabled in FCR mode. 

Note:

 

Any field current reference less than 0.000 Adc 

will become 0.000 Adc.

Features and Protection

GPN046 04-13.indd   10

4/5/13   10:24 AM

Содержание DVR 2000E+









































































Отзывы: