Marathon Electric DVR 2000E+ Скачать руководство пользователя страница 23

Страница: 23 / 72

CONNECTIONS

ELECTRICAL HAZARD

Failure to connect the voltage regulator in accor-

dance with the manufacturer’s documentation may

result in serious personal injury, death, and/or

property damage.

ELECTRICAL SHOCK HAZARD

Failure to follow these instructions may result in

serious personal injury, death, and/or property

damage.

Installation and repair of electrical generators

and voltage regulators should be attempted

by qualified personnel only. Electrical con-

nections shall be made by a qualified electri-

cian in accordance with all local, national,

international and/or other applicable codes,

rules or regulations and sound practices.

Do not touch electrically live parts.

Disconnect, lockout and tag prime mover

and input power supplies before installing or

servicing voltage regulator. Use a voltmeter

to verify that power is off before contacting

conductors.

Do not open terminal box or touch unpro-

tected terminals while the generator shaft

is rotating. Shaft rotation produces voltage

in generators even when no excitation is

applied. Residual voltage is present at the

generator leads and regulator connections

even when the regulator fuse is removed.

Ground (earth) regulator in accordance with

local, national, international and/or other

applicable codes, rules or regulations.

Incorrect wiring may damage the unit.

Note: Be sure that the DVR

is hard-wired to earth

ground with no smaller than 12 AWG copper wire

attached to the ground terminal on the rear of the

unit case. When the unit is configured in a system

with other devices, it is recommended to use a

separate lead to the ground bus from each device.

DVR

connections are dependent on the application.

DVR

Connectors

DVR

units have four types of interface connectors.

All connectors are located on the rear of the unit.

1. Ten (10) 1/4”, quick-connect terminals for

generator connections

2. Two (2) 12-pin Deutsch (DTC style) connec-

tors for current transformer (CT) and system

interface connections

3. One (1) 3-pin Amp/Tyco Mini Mate-N-Lok

receptacle for the Controlled Area Network

(CAN) bus interface.

4. One (1) 9-pin DB-9 type connector for the

communication between the DVR

and

DVRPortal™.

Wires performing common functions, such as volt

age sensing leads, should be grouped together.

Figure 5-4 shows the quick disconnect terminal con

nections located on the rear panel of the DVR

Installation

GPN046 04-13.indd 21

4/5/13 10:24 AM

Содержание DVR 2000E+









































































Результаты поиска

Содержание DVR 2000E+

Отзывы:

Бренды по названию

Популярные бренды

Marathon Electric DVR 2000E+, Руководство пользователя

Результаты поиска

Содержание DVR 2000E+

Отзывы:

Бренды по названию

Популярные бренды