Manitowoc 1814E Скачать руководство пользователя страница 2

 

 

NOTICE 

IF, DURING THE WARRANTY PERIOD, THE CUSTOMER USES A PART FOR THIS MANITOWOC FOOD SERVICE 
EQUIPMENT OTHER THAN AN UNMODIFIED NEW OR RECYCLED PART PURCHASED DIRECTLY FROM FRYMASTER  
OR ANY OF ITS AUTHORIZED SERVICERS, AND/OR THE PART BEING USED IS MODIFIED FROM ITS ORIGINAL 
CONFIGURATION, THIS WARRANTY WILL BE VOID.  FURTHER, FRYMASTER AND ITS AFFILIATES WILL NOT BE 
LIABLE FOR ANY CLAIMS, DAMAGES OR EXPENSES INCURRED BY THE CUSTOMER WHICH ARISE DIRECTLY OR 
INDIRECTLY, IN WHOLE OR IN PART, DUE TO THE INSTALLATION OF ANY MODIFIED PART AND/OR PART 
RECEIVED FROM AN UNAUTHORIZED SERVICER. 

 

 

NOTICE 

This appliance is intended for professional use only and is to be operated by qualified personnel only. A Frymaster 
Factory Authorized Servicer (FAS) or other qualified professional should perform installation, maintenance, and 
repairs.  Installation, maintenance, or repairs by unqualified personnel may void the manufacturer’s warranty.  See 
Chapter 1 of this manual for definitions of qualified personnel. 

 

 

NOTICE 

This equipment must be installed in accordance with the appropriate national and local codes of the country and/or 
region in which the appliance is installed.  See NATIONAL CODE REQUIREMENTS in Chapter 2 of this manual for 
specifics.  

 

 NOTICE 

When installed, this appliance must be electrically grounded in accordance with local codes, or in the absence of 
local codes, with the National Electrical Code, ANSI/NFPA 70, the Canadian Electrical Code, CSA C22.2, or the 
appropriate national code of the country in which installed.

 

 

 

NOTICE TO U.S. CUSTOMERS 

This equipment is to be installed in compliance with the basic plumbing code of the Building Officials and Code 
Administrators International, Inc. (BOCA) and the Food Service Sanitation Manual of the U.S. Food and Drug 
Administration. 

 

 

NOTICE 

This appliance is intended to be used for commercial applications, for example in kitchens of restaurants, canteens, 
hospitals and in commercial enterprises such as bakeries, butcheries, etc., but not for continuous mass production 
of food. 

 

 WARNING 

This equipment is intended for indoor use only.  Do not install or operate this equipment in outdoor areas. 

 

 

NOTICE 

The appliance must be installed and used in such a way that any water cannot contact the fat or oil.   

 

 

NOTICE 

Drawings and photos used in this manual are intended to illustrate operational, cleaning and technical procedures 
and may not conform to onsite management operational procedures. 

 

NOTICE TO OWNERS OF UNITS EQUIPPED WITH CONTROLLERS 

U.S. 

This device complies with Part 15 of the FCC rules.  Operation is subject to the following two conditions:  1) This 
device may not cause harmful interference, and 2) This device must accept any interference received, including 
interference that may cause undesired operation.  While this device is a verified Class A device, it has been shown to 
meet the Class B limits. 

CANADA 

This digital apparatus does not exceed the Class A or B limits for radio noise emissions as set out by the ICES-003 
standard of the Canadian Department of Communications.

  

Cet appareil numerique n’emet pas de bruits radioelectriques depassany les limites de classe A et B prescrites dans 
la norme NMB-003 edictee par le Ministre des Communcations du Canada. 

 

 WARNING 

Do not use water jets to clean this equipment. 

Содержание 1814E











































Отзывы: