4 - N/A
This device warns the operator that the lift truck is approaching the limit of longitudinal stability. However, lateral stability can
reduce the load chart in the upper part, and this reduction is not detected by the longitudinal stability alarm.
The operator must always respect the lift truck load chart.
OPERATION
When the lift truck is switched on a control test is automatically carried out.
- Correct operation: All leds and the sound alarm function continuously for 2 seconds.
- Faulty operation: All leds and sound alarm function intermittently (stop the lift truck and consult your dealer, never attempt a
repair yourself).
A - LEDS (VISUAL ALARM) (FIG. A)
A1 - 4 green leds: There is a large reserve of longitudinal stability.
A2 - 2 yellow leds: The lift truck is approaching the limit of longitudinal stability,
move carefully.
A3 - 1 red led: The lift truck is very near at the limit of longitudinal stability. The
alarm sounds simultaneously with a slow intermittent sound.
Move very carefully.
A4 - 1 red led: The lift truck is at the authorized limit of longitudinal stability. The
alarm sounds simultaneously with a speed intermittent sound.
Only make de-aggravating hydraulic movements in the following
order ; retract and raise the jib.
B - SOUND ALARM SWITCH (FIG. A)
Used to switch off the sound alarm when using the lift truck with loading and earth moving
buckets. When it is switched off, the red led B1 indicates that the sound alarm has been
cut off and only the visual alarm is working. Under other operating conditions, the sound
alarm must be switched on.
C - TEST SWITCH (FIG. A)
Press the switch to verify at any time that the longitudinal stability alarm is working.
NOTE: This test does not verify that the alarm is correctly set ; this must be checked at
every periodic service.
- Correct operation: All leds and the sound alarm function continuously.
- Faulty operation: All leds and the sound alarm function intermittently (stop the lift truck
and consult your dealer, never attempt a repair yourself).
D - STRAIN GAUGE (FIG. B)
Disassembly or adjustment of the strain gauge is prohibited, this must only be done by
specially trained personnel, consult your dealer.
MT 728 Série C-E2
MT 928 Série C-E2
NOTE: The cutting-off of "SIMPLE" hydraulic movements is installed in series (See: 2 - DESCRIPTION: DESCRIPTION AND USE
OPTIONS).
5 - SWITCH PANEL
NOTE: The location of the switches may vary depending on the options.
A - OPTION
MT 732 Série C-E2
MT 732 Turbo Série C-E2
MT 932 Série C-E2
MT 932 Turbo Série C-E2
MT 1030 S Série 3-E2
MT 1030 S Turbo Série 3-E2
- OPTION Electrical jib provision (See: 2 - DESCRIPTION: DESCRIPTION AND USE
OPTIONS).
B - OPTION
A
B
A2
A1
A1
A1
A1
A2
A3
A4
A
B
B1
C
D
A
B
C
D
E
F
G
H
2
1
2 - 22
Содержание MT 732
