Mandik HELIOS, Инструкция по установке, эксплуатации и техническому обслуживанию

Страница: 31 / 40

31
Natural
gas
Propane
G31
Natural
gas
Propane
G31
Natural gas
Propane
G31
Natural gas
Propane
G31
5,5 3,8 5,5 3,8 5,5 3,8 6,2 4,2
G20: 10,5
21,0
G20: 10,5
21,0
G20: 10,5
21,0
G20: 10,5
17,0
G25: 13,5 G25: 13,5 G25: 13,5 G25: 13,5
G20: 41,0
41,0
G20: 41,0
41,0
G20: 41,0
41,0
G20: 49,5
49,5
G25: 38,2 G25: 38,2 G25: 38,2 G25: 46,1
130 - 138 143 - 150 148 - 155 153 - 163 130 - 138 143 - 150 165 - 173 173 - 185
7,0 - 7,8
7,8 - 8,5
7,0 - 7,8
7,8 - 8,5
7,0 - 7,8
7,8 - 8,5 5,6 - 6,0 8,3 - 9,0
0 - 10 0 - 20 0 - 10 0 - 20 0 - 10 0 - 20 0 - 10 0 - 10
100 - 170 130 - 190 100 - 170 130 - 190 100 - 170 130 - 190 100 - 170 130 - 190
7,5 - 7,9 7,8 - 8,1 7,5 - 7,9 7,8 - 8,1 7,5 - 7,9 7,8 - 8,1 8,6 - 8,3 7,8 - 8,4
93,0 - 94,0 92,6 - 93,5 92,0 - 93,0 91,0 - 92,0 93,0 - 94,0 92,6 - 93,5 92,5 - 93,0 92,5 - 93,0
– –
G20: 8,2
16,5
G20: 8,2
16,5
G20: 8,2
14,5
G25: 10,5 G25: 10,5 G25: 10,5
– – 36,0 36,1 36,0 36,1 43,6 43,5
1. Turn the switch „ - STOP - “to the position „STOP“.
2. In case of the long-term breakdown it is suitable to close the gas closing valve in front of the heater.
1. Turn the main electric switch „ “ to the position „1“.
2. Turn the switch „ - STOP - “ to the position „ “ or „ “ (in this case the infra heater operation
is performed under the automatic mode which it is necessary to program according to the relevant
control box instructions). The green indicator of the electric supply „ “ lights up on the control box,
also green indicator on the bottom of burner box will light on.
3. After finishing the ventilation time (app. 50 s), the infrared heater will start and the green light " " on
control box and orange indicator on the bottom of burner box will light on.
4. In case the burner is not fired (the orange lamp of operation on the control box is not alight), the cycle
is repeated twice. If it does not ignite even the third time, the red indicator light on the burner box lights
up to indicate an error. For unblocking the error state, the power supply of the heater must be
disconnected and reconnected (switch " - STOP- " to "STOP" and then back to " " or " " .
If even after several ignition cycles the infra heater is not started, call the service organisation.
5. The output of the two-stage infrared heaters controlled by the can be changed by the " " switch.
"OID" control box controls the power level of the two-stage heaters automatically.