manualshive.com logo in svg

Man D 0836 LE 401, Руководство по эксплуатации

Поделиться
Скачать
Man D 0836 LE 401 Скачать руководство пользователя страница 61

Maintenance and care

61

Parallel fuel filter

Draining moisture:

Unsrew drain plugs at every oil change
until moisture has been discharged and
clean fuel flows out

Changing fuel filter

Only when the engine is swiched off.

D

Remove filter cartridge using tape
wrench.

D

Wet seal on new filter with fuel

D

Screw on filter by hand

D

After this, bleed the fuel system

D

Check filter for leaks

Caution:

Used fuel filters are classed as
dangerous waste and must be dis-
posed of accordingly.

Change-over fuel filter

Where the changeover-type filter is in-
stalled, the servicing procedure is for the
filter side requiring to be shut off with the
engine running. During continuous oper-
ation position the selector lever that both
filter halves are in operation.

Caution:

Do not leave selector lever in any
intermediate position because this
would be liable to interfere with
fuel supply. If in doubt stop the en-
gine to change the fuel filter.

Continuous operation
(both filter halves
in operation)

Right-hand filter 
cut out

Left-hand filter
cut out

Содержание D 0836 LE 401













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды