manualshive.com logo in svg

Malossi 3114443, Руководство пользователя

Поделиться
Скачать
Malossi 3114443 Скачать руководство пользователя страница 29

- 29 -

Réglage TPS (Throttle position sensor) – Fig. 17
- Tournez le trimmer “LOW” sur la fl èche rouge.
- Tournez la clé du véhicule sur ON.
- Attendre l’allumage complet des 3 leds et ensuite l’arrêt complet de celles-ci.

- Tournez la clé du véhicule sur OFF.
- Portez le trimmer sur ZERO.
- Tournez le trimmer “HIGH” sur la fl èche rouge.
- Ouvrez complètement la poignée GAZ.
- Tournez la clé du véhicule sur ON
- Attendre l’allumage complet des 3 leds et ensuite l’arrêt complet de celles-ci.
- Tournez la clé du véhicule sur OFF.

TPS (Throttle Position Sensor) Calibration – Fig. 17
- Rotate the “LOW” trimmer to the red arrow position.
- Turn the ignition key to the “ON” position.
- Wait for all three (3) LEDs to illuminate and then turn off.

- Turn the ignition key to the “OFF” position.
- Rotate the “LOW” trimmer to the “ZERO (0)” position.
- Rotate the “HIGH” trimmer to the red arrow position.
- Turn the throttle to the fully open position.
- Turn the ignition key to the “ON” position.
- Wait for all three (3) LEDs to illuminate and then turn off.
- Turn the ignition key to the “OFF” position.

Taratura TPS (throttle position sensor) – Fig. 17
- Ruotare il trimmer “LOW” sulla freccia rossa.
- Ruotare la chiave del veicolo su ON.
- Attendere la completa accensione dei 3 led e il successivo spegnimento.

- Ruotare la chiave del veicolo su OFF.
- Portare il trimmer sullo zero.
- Ruotare il trimmer “HIGH” sulla freccia rossa.
- Aprire completamente la manopola del gas.
- Ruotare la chiave del veicolo su ON.
- Attendere la completa accensione dei 3 led e il successivo spegnimento.
- Ruotare la chiave del veicolo su OFF.

Содержание 3114443





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды