background image

Front Loading Utensil Washer Disinfector (WDF)

 

Operation, Maintenance and Installation Manual

 

Issue 1 

Page

 31

  

20/01/2022 

Warranty Statement 

This warranty is provided, and operates in addition to, the statutory warranties Malmet  (Australia) Pty Ltd ("

Malmet

") provides 

to any consumer under the Australian Consumer Law (if applicable) or by virtue of any other applicable legislation. 

Subject  to  the  following  conditions,  we  provide,  from  the  date  of  purchase,  the  following  warranty  on Malmet devices and spare parts 
for products manufactured by Malmet and sold in Australia: 

• 

Functional components found within the device to be defective in workmanship or material will be  repaired or replaced free of 
charge subject to the periods of warranty specified in the table below. 

• 

A decision regarding whether the defective components will  be repaired or replaced will be determined at  the  sole  discretion 
of Malmet or its authorised agents or representatives. 

• 

The  structural  warranty  covers  any  structural  components  within  the  device,  which  fail  to  perform  their intended function 
due to faulty manufacture or deterioration within the warranty period. 

• 

Parts replaced  in devices under warranty  are warranted  for the balance  of the original  warranty  period  for that device. 

Malmet Devices 

 

Device Components 

 

Parts & Labour 

 

Structural Guarantee 

 

2 Years from Date of Purchase 

 

All other components 

 

2 Years from Date of Purchase 

 

 

Malmet Spare Parts 

1 Year from Date of Purchase 

 

The installer is responsible for the correct installation, start up and demonstrating the operation of the product.  They are also responsible for 
issuing the relevant certificates of compliance (these may differ from state to state). 

CONDITIONS AND EXCLUSIONS 

• 

Device must be installed and commissioned according to Malmet’s instructions (outlined in Malmet Operation, Maintenance and 
Installation Manual) and operated to the purpose it was designed. 

• 

Device must be serviced as instructed in the Operation, Maintenance and Installation Manuals. 

• 

To the extent permitted by law, this warranty shall not cover damage, malfunction or failure resulting from accident, misuse or 
misapplication, improper or unauthorised repair, neglect or modification or use of unauthorised replacement parts or accessories, 
inclusive of detergent, or improper voltage.  The warranty may be void if the serial number is removed or altered. 

• 

Parts damaged in transit back to Malmet Leeton due to poor packaging could result in warranty claim being rejected in part or in full. 

• 

Any  part  tampered  with  or  which  has  been  altered  by  unauthorised  repairs  and/or  modifications  will  be  rejected  under  a 
warranty claim to the extent permitted by law (to the extent the Australian Consumer Law applies, Malmet will assess the 
extent to which the tampering or unauthorised repairs contributed to the failure). 

• 

Reasonable access must be allowed for maintenance. If any additional equipment is needed to provide access to the device, 
this must be provided (and paid for) by the owner. 

• 

It is the owner's responsibility to provide safe access to the device. Malmet, or any of its authorised service agents, may refuse to perform 
maintenance or warranty work if access is unsafe, as determined by Malmet or any of its authorised service agents acting reasonably. 

• 

Should a warranty claim be rejected you will be advised in writing with a full explanation of our reasons. 

• 

Malmet have a Warranty Claim Procedure that is fair to our customers and provides an efficient system of replacement and/or repair of 
faulty parts. If at any time you believe we are not meeting our commitment to you please contact Malmet Head Office via email: 

[email protected]

 

• 

To the extent permitted by law, no responsibility will be accepted for outside elements including, but not limited to storms, pest and 
vermin that may cause damage to the device

.

 

• 

To the extent permitted by law, no responsibility will be accepted for damage incurred as a result of, or incidental to, electrical surges or 
brown outs or for any other consequential damages. 

• 

If there is no certificate of compliance for plumbing or electrical, Malmet reserves the right to refuse service on non-compliant 
installations. 

• 

To the extent permitted by law, claims for damage to contents, carpet, ceilings, foundations or any other consequential loss either direct 
or indirect resulting from, power spikes, incorrect operation, incorrect installation, faulty product or any other cause, are excluded. 

Содержание WDF-3020




































Отзывы: