background image

A battery short can cause a large current flow, 
overheating, possible burns and even a 
breakdown. 

6. 

Do not store the tool and battery cartridge in
locations where the temperature may reach or 
exceed 50

C (122

F). 

7. 

Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire. 

8. 

Be careful not to drop or strike battery.

9. 

Do not use a damaged battery.

10. 

Follow your local regulations relating to
disposal of battery.

SAVE THESE INSTRUCTIONS. 

Tips for maintaining maximum battery life 

1. 

Charge the battery cartridge before
completely discharged. 
Always stop tool operation and charge the
battery cartridge when you notice less tool
power. 

2. 

Never recharge a fully charged battery
cartridge. 
Overcharging shortens the battery service life. 

3. 

Charge the battery cartridge with room
temperature at 10

C - 40

C (50

F - 104

F). 

Let a hot battery cartridge cool down before
charging it. 

4. 

Charge the battery cartridge once in every six
months if you do not use it for a long period of 
time. 

FUNCTIONAL DESCRIPTION 

CAUTION: 

• 

Always be sure that the tool is switched off and the 
battery cartridge is removed before adjusting or
checking function on the tool. 

Installing or removing battery cartridge 

CAUTION: 

• 

Hold the tool and the battery cartridge firmly
when installing or removing battery cartridge.

Failure to hold the tool and the battery cartridge
firmly may cause them to slip off your hands and
result in damage to the tool and battery cartridge
and a personal injury. 

1

2

3

012445 

• 

Always switch off the tool before installing or
removing of the battery cartridge. 

• 

To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge. 

• 

To install the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing 
and slip it into place. Always insert it all the way
until it locks in place with a little click. If you can see 
the red indicator on the upper side of the button, it is 
not locked completely. Install it fully until the red
indicator cannot be seen. If not, it may accidentally
fall out of the tool, causing injury to you or someone 
around you. 

Do not use force when installing the battery cartridge. If 
the cartridge does not slide in easily, it is not being 
inserted correctly. 

Battery protection system   
(Lithium-ion battery with star marking) 

1

012128 

1. Star marking 

1. Red indicator 
2. Button 
3. Battery cartridge

Содержание XHU02M1












Отзывы: