background image

10 

1

1

2

3

012451 

Loosen four screws and remove the blades. Remove the 
washer and sponge from the shear blades and put them 
aside. They are required for the later installation. 

1

2

3

4

012481 

If the sleeves are still left in the holes of the gear, remove 
the gear and push the sleeves out of it with a screwdriver 
or the like. 

NOTE: 

The washer underneath the gear may come off by 
mistake when removing the gear. In this case, return it to 
the original position as it was installed. 

Installing the shear blade 

1

012450 

Remove the blade cover from the old shear blades and fit 
it onto the new ones to avoid contact with blades. 

012490 

Adjust the hole positions by turning the gear as illustrated. 

1

012454 

1

012455 

Apply some grease provided with the new shear blades 
as illustrated. 

1

2

3

012482 

Put the removed sponge in the same position as the old 
one. Make sure that the sleeves provided with the new 
shear blades are put on the pins of the blade. Place the 
new shear blades on the tool so that the pins fit in the 
holes of the gear. If the sleeves on the pins come off 
mistakenly, put them into the holes of the gear 
beforehand. 

1

1

2

012452 

Install the blade and tighten the four screws and put the 
removed washer in the same position as the old one. 

1. Screws
2. Washer 

1. Blade 
2. Sponge 
3. Sleeves 

1. Grease 

1. Grease 

1. Blade cover 

1. Gear 
2. Sleeves 
3. Washer 
4. Groove 

1. Screws
2. Sponge 
3. Washer 

Содержание XHU02M1












Отзывы: