background image

Indication lamp 

1

012480 

Running the tool allows the indication lamp to show the 
battery cartridge capacity status. 
When the tool is also overloaded and has stopped during 
operation, the lamp lights up in red. 
Refer to the following table for the status and action to be 
taken for the indication lamp. 

Note 1: When attempting to switch the tool on, the indicator light may continue to come on  

due to the tool and/or the battery pack being too warm.

Red Indicator Light

Light Blinks

Light Stays On 
(See Note 1 below)

Condition

This indicates the battery  
level is getting low.  

The remaining battery capacity  
is too low and the  tool  will  not   
operate.

The battery protection system  
has been activated due to the  
tool being overloaded.

Action to be taken

Recharge the battery cartridge.

Remove and recharge the  
battery.

Release the switch trigger  on  
the tool and stop the application  
that caused the tool to become  
overloaded.   
Then pull the switch trigger again  
to restart.

The battery tool and battery pack will need to be allowed to cool down before  
further use.

013094 

OPERATION 

CAUTION: 

• 

Be careful not to accidentally contact a metal fence 
or other hard objects while trimming. The blade will 
break and may cause serious injury. 

• 

Overreaching with a hedge trimmer, particularly
from a ladder, is extremely dangerous. Do not work 
from anything wobbly or infirm. 

007559 

1. Indication lamp

Содержание XHU02M1












Отзывы: