Makita ST113D, Инструкция по эксплуатации

Страница: 7 / 62

7 ENGLISH
ASSEMBLY
CAUTION:
Always make sure that the battery
cartridge is removed before carrying out any work
on the stapler.
Staples
CAUTION:
Do not use staples other than
designated in this manual or staples that appear
to be damaged, bent, rusty or corroded.
CAUTION:
Load the same type, size and
uniform length of staples when loading multiple
strips of staples in the magazine.
NOTICE:
Handle the staples and their box carefully.
If the staples have been handled roughly, they may be
bent out of shape, causing poor staple feed or jamming.
NOTICE:
Avoid storing the staples in a very humid
or hot place or place exposed to direct sunlight.
Loading staples
WARNING:
When loading staples, always
make sure that the battery cartridge is removed
from the stapler. Unintentional firing may cause
personal injuries and property damage.
CAUTION:
After loading staples, make sure
that the sub magazine is surely closed. F alling
staples out of the magazine may cause an injury to
th e operator or by stand er, espec ially w h en w orking in
h igh loc ations.
1.
R emov e th e battery c artrid ge.
2. P ress th e loc king lev er and slid e th e sub maga-
z ine bac kw ard .
► Fig.6: 1. L oc king lev er 2. S ub magaz ine
3. L oad staples into th e main magaz ine w ith th eir
f eet f ac ing up.
► Fig.7: 1. S taples 2. Main magaz ine
4. A f ter load ing staples, push bac k th e sub-maga-
z ine in plac e until it c lic ks.
T o remov e staples, f ollow th e installation proc ed ures in
rev erse.
Hook
CAUTION:
Do not hang the hook from the
waist belt. D ropping th e stapler, w h ic h is c aused by
th e h ook ac c id entally c oming out of plac e, may c ause
unintentional firing and result in personal injuries.
► Fig.8
T h e h ook is c onv enient f or temporarily h anging th e tool.
T h is c an be installed on eith er sid e of th e tool.
T o install th e h ook, insert it into a groov e in th e tool
h ousing on eith er sid e and th en sec ure it w ith a sc rew .
T o remov e, loosen th e sc rew and th en take it out.
► Fig.9: 1. G roov e 2. H ook 3. S c rew
OPERATION
Testing the safety system
WARNING:
Make sure all safety systems are
in working order before operation. Failure to do
so may cause personal injuries.
►
Fig.10: 1.
T rigger-loc k button
2.
S w itc h trigger
3. C ontac t element 4. S ub magaz ine
T est saf ety sy stems f or possible f ault bef ore operation
as f ollow s.
1. U nload staples f rom th e tool and keep th e sub
magaz ine opened .
2. I nstall th e battery c artrid ge.
3. O nly pull th e sw itc h trigger w ith out touc h ing th e
c ontac t element against th e material.
4. O nly touc h th e c ontac t element against th e mate-
rial w ith out pulling th e sw itc h trigger.
I f th e tool operates in th e c ase of 3 and 4 abov e, th e
saf ety sy stems are f aulty . S top using th e tool immed i-
ately and ask y our loc al serv ic e c enter.
Driving staples
WARNING:
Continue to place the contact
element firmly on the material until the staple is
driven completely.
Unintentional firing may cause
personal injuries.
► Fig.11: 1. S w itc h trigger 2. C ontac t element 3. F ront
part 4. R ear part
Y ou c an operate th e tool in eith er w ay of “ single
seq uential ac tuation” or “ c ontac t ac tuation” .
Single sequential actuation:
I n th is mod e, y ou c an d riv e one staple by one seq uen-
tial operation.
1. Place flat the contact element on the material.
2. H old both of th e f ront part and th e rear part of th e
tool firmly against the material.
3.
P ull th e sw itc h trigger f ully to d riv e th e staples.
4. Release your finger from the switch trigger before
mov e th e c ontac t element f rom th e material.
Contact actuation:
I n th is mod e, y ou c an d riv e staples seq uentially .
1. P ull th e sw itc h trigger.
2. With the switch trigger pulled, place flat the con -
tac t element on th e material to d riv e th e staples.
3. Move the tool to the next area and place flat the
c ontac t element on th e material again.
NOTE: T h e groov e ind ic ates th e point th at staple is
d riv en.
► Fig.12: 1. G roov e
I f th e h ead of th e staple remains abov e th e w orkpiec e
surf ac e, d riv e th e staple w h ile h old ing th e stapler h ead
firmly against the workpiece.
► Fig.13