Makita ST113D, Инструкция по эксплуатации

Страница: 6 / 62

6 ENGLISH
FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car -
tridge firmly when installing or removing battery
cartridge.
F ailure to h old th e tool and th e battery
cartridge firmly may cause them to slip off your hands
and result in d amage to th e tool and battery c artrid ge
and a personal injury.
► Fig.1: 1. R ed ind ic ator 2. Button 3. Battery c artrid ge
T o remov e th e battery c artrid ge, slid e it f rom th e tool
w h ile slid ing th e button on th e f ront of th e c artrid ge.
T o install th e battery c artrid ge, align th e tongue on th e
battery c artrid ge w ith th e groov e in th e h ousing and slip
it into plac e. I nsert it all th e w ay until it loc ks in plac e
w ith a little c lic k. I f y ou c an see th e red ind ic ator on th e
upper sid e of th e button, it is not loc ked c ompletely .
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. I f not,
it may accidentally fall out of the tool, causing injury to
y ou or someone around y ou.
CAUTION:
Do not install the battery cartridge
forcibly. I f th e c artrid ge d oes not slid e in easily , it is
not being inserted c orrec tly .
Battery protection system
T h e tool is eq uipped w ith a battery protec tion sy stem.
T h is sy stem automatic ally c uts of f pow er to th e motor to
ex tend battery lif e.
T h e tool w ill automatic ally stop d uring operation if th e
tool and / or battery are plac ed und er one of th e f ollow ing
c ond itions:
Overloaded:
T h e tool is operated in a manner th at c auses it to d raw
an abnormally h igh c urrent.
I n th is situation, turn th e tool of f and stop th e applic ation
th at c aused th e tool to bec ome ov erload ed . T h en turn
th e tool on to restart.
I f th e tool d oes not start, th e battery is ov erh eated . I n
th is situation, let th e battery c ool bef ore turning th e tool
on again.
Low battery voltage:
T h e remaining battery c apac ity is too low and th e tool
w ill not operate. I f y ou turn th e tool on, th e motor d oes
not run or th e motor runs again but stops soon. I n th is
situation, remov e and rec h arge th e battery .
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
► Fig.2: 1. I nd ic ator lamps 2. C h ec k button
P ress th e c h ec k button on th e battery c artrid ge to ind i-
c ate th e remaining battery c apac ity . T h e ind ic ator lamps
ligh t up f or a f ew sec ond s.
Indicator lamps Remaining
capacity
Lighted Off
75 % to 1 00%
5 0% to 75 %
25 % to 5 0%
0% to 25 %
NOTE: D epend ing on th e c ond itions of use and th e
ambient temperature, th e ind ic ation may d if f er sligh tly
f rom th e ac tual c apac ity .
Switch action
CAUTION:
Before installing the battery car -
tridge into the tool, always check to see that the
switch trigger actuates properly and returns to
the "OFF" position when released.
CAUTION:
When not operating the tool,
depress the trigger-lock button from B side to
lock the switch trigger in the OFF position.
► Fig.3: 1. T rigger-loc k button 2. S w itc h trigger
► Fig.4
T o prev ent th e sw itc h trigger f rom ac c id entally pulled ,
th e trigger-loc k button is prov id ed .
T o pull th e sw itc h trigger, d epress th e trigger-loc k button
f rom A sid e.
A f ter use, alw ay s press in th e trigger-loc k button f rom
B sid e.
Lighting up the lamp
CAUTION:
Do not look in the light or see the
source of light directly.
► Fig.5: 1. L amp
P ull th e sw itc h trigger or ac tuate th e c ontac t element to
ligh t up th e lamp. T h e lamp keeps on ligh ting w h ile pull-
ing th e sw itc h trigger or ac tuating th e c ontac t element.
T h e lamp goes out approx imately 1 0 sec ond s af ter
releasing th e sw itc h trigger and th e c ontac t element.
NOTE:
U se a d ry c loth to w ipe th e d irt of f th e lens of
th e lamp. Be c aref ul not to sc ratc h th e lens of lamp, or
it may low er th e illumination.