Makita ST113D, Инструкция по эксплуатации

Страница: 5 / 62

5 ENGLISH
7. Always wear safety goggles or safety glasses with
side shield, and a full face shield when needed.
8 . Keep hands and feet away from the ejection
port area.
9 . Always remove the battery cartridge before
loading the fasteners, adjustment, inspection,
maintenance or after operation is over.
1 0. Make sure no one is nearby before operation.
Never attempt to drive fasteners from both the
inside and outside of wall at the same time.
Fasteners may rip through and/or fly off, pre -
senting a grave danger.
1 1 . Watch your footing and maintain your balance
with the tool. Make sure there is no one below
when working in high locations.
1 2. Check walls, ceilings, floors, roofing and
the like carefully to avoid possible electrical
shock, gas leakage, explosions, etc. caused by
stapling into live wires, conduits or gas pipes.
1 3. Use only fasteners specified in this manual.
The use of any other fasteners may cause
malfunction of the tool.
1 4 . Do not tamper with the tool or attempt to use it
for other than driving fasteners.
1 5 . Do not operate the tool without fasteners. It
shortens the service life of the tool.
1 6 . Stop driving operations immediately if you
notice something wrong or out of the ordinary
with the tool.
1 7. Never fasten into any materials which may
allow the fastener to puncture and fly through
as a projectile.
1 8 . Never actuate the switch trigger and contact
element until you are prepared to fasten work-
pieces. Never defeat its purpose by securing
the contact element back or by depressing it
by hand.
1 9 . Never tamper with the contact element. Check
the contact element frequently for proper
operations.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
Important safety instructions for
battery cartridge
1 . Before using battery cartridge, read all instruc-
tions and cautionary markings on ( 1) battery
charger, (2) battery, and (3) product using battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4 . If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten -
tion right away. It may result in loss of your
eyesight.
5 . Do not short the battery cartridge:
( 1 ) Do not touch the terminals with any con -
ductive material.
( 2) Avoid storing battery cartridge in a con -
tainer with other metal objects such as
nails, coins, etc.
( 3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
flow, overheating, possible burns and even a
breakdown.
6 .
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 °C (122 °F).
7.
Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8 .
Be careful not to drop or strike battery.
9 . Do not use a damaged battery.
1 0. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require -
ments.
F or c ommerc ial transports e.g. by th ird parties,
f orw ard ing agents, spec ial req uirement on pac k-
aging and labeling must be observ ed .
F or preparation of th e item being sh ipped , c onsult-
ing an ex pert f or h az ard ous material is req uired .
P lease also observ e possibly more d etailed
national regulations.
T ape or mask of f open c ontac ts and pac k up th e
battery in suc h a manner th at it c annot mov e
around in th e pac kaging.
1 1 . Follow your local regulations relating to dis-
posal of battery.
1 2. Use the batteries only with the products
specified by Makita. I nstalling th e batteries to
non-compliant products may result in a fire, exces -
siv e h eat, ex plosion, or leak of elec troly te.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
U se of non-genuine Makita batteries, or batteries th at
h av e been altered , may result in th e battery bursting
causing fires, personal injury and damage. It will
also v oid th e Makita w arranty f or th e Makita tool and
c h arger.
Tips for maintaining maximum
battery life
1 . Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car -
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem -
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.