background image

R

epair

P 5 / 15 

3. Sleeve is in the lock  position. In order to free from  lock position, pull sleeve toward the blade installing side.
    (When the sleeve is free from lock,  pin 3 (long) is at the position illustrated in Fig. 5.  

4. Holding the top of slider with your finger, remove sleeve by pushing pin 3 (long) with a small sticker 
    through slider as illustrated in Fig. 6.
   < Note > When removing sleeve, always hold the top of slider with your finger as illustrated in Fig. 6.
                  Otherwise, push  plate and compression spring 2 can spring out from slider as illustrated in Fig. 6A,
                  and they will get lost.
    After removing sleeve, take off push plate, compression spring 2  and torsion spring 17 from slider
    as illustrated in Fig. 6B.

Fig. 5

Sleeve

Pin 3 (long)

Torsion spring 17

Slider

Blade installing side

Gear housing side

Pull the sleeve to this
direction.

Fig. 6

Fig. 6A

Push plate

Compression spring 2

Fig. 6B

Torsion spring 17

Compression spring 2

Push plate

Sleeve

Sleeve

Pin 3

Pin 3

Sleeve

(3) Assembling blade clamp section

1. Assemble torsion spring 17 to slider. And then, set compression spring 2 into slider.
   <Note> Pay attention to the position of the tail of torsion spring 17. It has to come to the right side 
                in the view from the side of shoe adjusting bolt M8x25, as illustrated in Fig. 7. 

Torsion spring 17

Slider

The tail of
torsion spring 17

Compression spring 2

Threaded hole for hex bolt M8x25

Fig. 7

Содержание MAKSTAR BJR240SF
















Отзывы: