![background image](http://html.mh-extra.com/html/makita/m9800-series/m9800-series_instruction-manual_1722846006.webp)
6 ENGLISH
22.
Keep bystanders a safe distance aw ay from
w ork area. Anyone entering the w ork area
must w ear personal protective equipment.
Fragments of workpiece or of a broken accessory
may fly away and cause injury beyond immediate
area of operation.
23.
Never lay the pow er tool dow n until the acces-
sory has come to a complete stop.
T h e spinning
accessory may grab the surface and pull the
pow er tool out of y our c ontrol.
24 .
Do not run the pow er tool w hile carrying it at
your side.
A c c id ental c ontac t w ith th e ac c essory
c ould snag y our c loth ing, pulling th e ac c essory
into your body.
25 .
Do not operate the power tool near flammable
materials.
S parks c ould ignite th ese materials.
26 .
Do not use accessories that require liquid
coolants.
U sing w ater or oth er liq uid c oolants
may result in elec troc ution or sh oc k.
27.
Alw ays be sure that the tool is sw itched off
and unplugged before carrying out any w ork
on the tool.
28 .
If w orking place is extremely hot and humid,
or badly polluted by conductive dust, use a
short-circuit breaker ( 30 mA) to assure opera-
tor safety.
29 .
Always be sure you have a firm footing. Be
sure no one is below w hen using the tool in
high locations.
30.
Before starting operation, make sure that there
is no hidden supply lines such as electric, gas
and w ater lines under the w orking surface.
Cutting or damaging the supply lines may cause
elec tric sh oc k, gas leakage, property d amage, or
oth er ac c id ents.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
w ith product ( gained from repeated use) replace
strict adherence to safety rules for the subject
product. MISUSE or failure to follow the safety
rules stated in this instruction manual may cause
serious personal injury.
FUNCTIONAL DESCRIPTION
CAUTION:
Alw ays be sure that the tool is
sw itched off and unplugged before adjusting or
checking function on the tool.
Sw itch action
CAUTION:
Before plugging in the tool, alw ays
check to see that the tool is sw itched off.
T o start th e tool, slid e th e slid e sw itc h tow ard th e " I
( O N) " position.
T o stop th e tool, slid e th e slid e sw itc h tow ard th e " O
( O F F ) " position.
►
Fig.1:
1.
S lid e sw itc h
Adjusting the orbital stroke rate
The orbital stroke rate is adjustable. To change the orbital
stroke rate, turn the dial between 1 and 5. The higher the
number is, the higher the orbital stroke rate is. Preset the
dial to the number suitable for your workpiece.
►
Fig.2:
1.
D ial
NOTE:
The dial cannot be turned directly from 1 to 5
or f rom 5 to 1 . F orc ing th e d ial may d amage th e tool.
W h en c h anging th e d ial d irec tion, alw ay s turn th e d ial
moving it through each intermediate number.
ASSEMBLY
CAUTION:
Alw ays be sure that the tool is
sw itched off and unplugged before carrying out
any w ork on the tool.
Installing or removing application tool
Optional accessory
WARNING:
Do not install application tool
upside dow n.
I nstalling applic ation tool upsid e d ow n
may damage the tool and cause serious personal injury.
WARNING:
Install attachment tool in the cor-
rect direction according to your w ork. Application
tool can be installed at an angle of every 30 degree.
WARNING:
Alw ays install the application tool so
that the protrusions of the tool flange fit in the holes
on the application tool.
F ailure to d o so may c ause th e
application tool flown off and result in personal injury.
WARNING:
When installing the application
tool, be sure to tighten the application tool instal-
lation bolt securely.
P ut an applic ation tool ( optional ac c essory ) on th e tool
flange so that the protrusions of the tool flange fit in the
h oles in th e applic ation tool and sec ure th e applic ation
tool by tightening the bolt firmly with the hex wrench.
W h en using sand ing applic ation tool, mount th e applic ation tool
on th e sand ing pad so th at it matc h es th e sand ing pad d irec tion.