![background image](http://html.mh-extra.com/html/makita/m9800-series/m9800-series_instruction-manual_1722846004.webp)
4 ENGLISH
ENGLISH ( Original instructions)
SPECIFICATIONS
Model:
M9800
O sc illation per minute
1 5 ,000 - 22,000 min
-1
O sc illation angle, lef t/ righ t
1 .6 ° ( 3.2 ° total)
O v erall length
28 3 mm
Net w eigh t
1 .2 - 1 .3 kg
S af ety c lass
/ I I
•
Due to our continuing program of research and development, the specifications herein are subject to change
w ith out notic e.
•
Specifications may differ from country to country.
•
The weight may differ depending on the attachment(s). The lightest and heaviest combination, according to
EPTA-Procedure 01/2014, are shown in the table.
Intended use
T h e tool is intend ed f or saw ing and c utting w ood ,
plastic , gy psum, non-f errous metals, and f astening
elements ( e. g. unh ard ened nails and staples) . I t is also
intend ed f or w orking sof t w all tiles, as w ell as d ry sand -
ing and sc raping of small surf ac es. I t is espec ially f or
working close to edge and flush cutting.
Pow er supply
The tool should be connected only to a power supply of
th e same v oltage as ind ic ated on th e nameplate, and
can only be operated on single-phase AC supply. They
are double-insulated and can, therefore, also be used
f rom soc kets w ith out earth w ire.
Noise
Work mode
Sound pres-
sure level
( L
pA
) :
Uncertainty ( K)
Applicable
standard
S and ing
78 d B( A )
3 d B( A )
EN6 28 4 1 -2-4
Cutting with
plunge c ut
saw blade
79 d B( A )
3 d B( A )
EN6 28 4 1 -1
Cutting with
segmental
saw blade
79 d B( A )
3 d B( A )
EN6 28 4 1 -1
S c raping
78 d B( A )
3 d B( A )
EN6 28 4 1 -1
T h e noise lev el und er w orking may ex c eed 8 0 d B ( A ) .
NOTE:
T h e d ec lared noise emission v alue( s) h as
been measured in accordance with a standard test
method and may be used for comparing one tool with
anoth er.
NOTE:
T h e d ec lared noise emission v alue( s)
may also be used in a preliminary assessment of
ex posure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the pow er tool can differ from the declared
value( s) depending on the w ays in w hich the
tool is used especially w hat kind of w orkpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use ( taking account of all parts of the operating
cycle such as the times w hen the tool is sw itched
off and w hen it is running idle in addition to the
trigger time) .
Vibration
The following table shows the vibration total value (tri-axial vector sum) determined according to applicable standard.
Work mode
Vibration emission
Uncertainty ( K)
Applicable standard
S and ing ( a
h
)
2.5 m/ s
2
1 .5 m/ s
2
EN6 28 4 1 -2-4
Cutting with plunge cut saw blade (a
h
)
8 .0 m/ s
2
1 .5 m/ s
2
EN6 28 4 1 -1
Cutting with segmental saw blade (a
h
)
4 .0 m/ s
2
1 .5 m/ s
2
EN6 28 4 1 -1
S c raping ( a
h
)
9 .5 m/ s
2
1 .5 m/ s
2
EN6 28 4 1 -1