25 ENGLISH
8.
When the cut is completed, switch off the tool and
wait until the blade has come to a complete stop
before returning the blade to its fully elevated position.
Compound cutting
Compound cutting is the process in which a bevel
angle is made at the same time in which a miter angle
is being cut on a workpiece. Compound cutting can be
performed at the angle shown in the table.
Miter angle
Bevel angle
Left and Right 0° - 45°
Left and Right 0° - 45°
When performing compound cutting, refer to "Press cut-
ting", "Slide (push) cutting", "Miter cutting" and "Bevel
cut" explanations
Cutting base boards
CAUTION:
Make sure to use the horizontal
'y)YX]'Y.#%#\\)yyY(:|
).\<]]'.^]
);#y)
board.
CAUTION:
When cutting the workpiece of the
]
'\$.)yy¢jjY(]
'..)(j#$)y<()]Y<y)#
spacer block to secure the workpiece.
When cutting the base board in 45° miter angle, engage
the stopper lever to prevent the blade case from con-
tacting the base board. This will keep the clearance
between the base board and the blade case when the
carriage is fully pushed forward.
{ !G>>G#">:?
capacity.
j
Fig.46:
1.
Stopper lever
2.
Spacer block
3.
Horizontal vise
Cutting crown and cove moldings
Crown and cove moldings can be cut on a compound
JJ@
There are two common types of crown moldings and
one type of cove moldings; 52/38° wall angle crown
molding, 45° wall angle crown molding and 45° wall
angle cove molding.
j
Fig.47:
1.
52/38° type crown molding
2.
45° type
crown molding
3.
45° type cove molding
" JJ
>X%} YYQYQ Q
:X%} YYQYQ Q
(a) (b)
(c) (d)
1
2
1.
Inside corner
2.
Outside corner
2
(a)
(b)
(a)
(b)
(b)
(a)
(b)
(a)
(a)
(b)
(c)
(d)
1
1.
Inside corner
2.
Outside corner
Measuring
JJJ
J A #JA J
of the workpiece's wall contact edge is the same as wall
length.
j
Fig.48:
1.
Workpiece
2.
Wall width
3.
Width of the
workpiece
4.
Wall contact edge
#J A
saw angles.
When cutting crown and cove moldings, set the bevel
Y#Q
position the moldings on the top surface of the saw
base as indicated in the table (B).
In the case of left bevel cut
(a) (b)
(c) (d)
1
2
1.
Inside corner
2.
Outside corner
Table (A)
–
Molding
position
in the
^<()
Bevel angle
Miter angle
52/38°
]:X)
¤ ¥]:X)
52/38°
]:X)
¤ ¥]:X)
For
inside
corner
(a)
Left
33.9°
Left 30°
Right
31.6°
Right
35.3°
(b)
Left
31.6°
Left
35.3°
For
outside
corner
(c)
(d)
Right
31.6°
Right
35.3°
Содержание LS1219
