22 ENGLISH
Removing and installing saw blade
WARNING:
%|#:y;)y<()] #]] )]YY%'y
switched off and unplugged before installing or
removing the blade.
#
WARNING:
y)Y.%:] )#$']#|().\ X(Y-
vided to install or remove the blade.
Failure to use
J
tightening of the hex socket bolt and serious personal
#JA J J
removing and installing the blade. Pull the stopper pin
and rotate it 90° with the carriage raised.
j
Fig.29:
1.
Unlocked position
2.
Locked position
3.
Stopper pin
Removing the blade
Loosen the hex bolt holding the center cover using the
hex wrench. Raise the blade guard and center cover.
j
Fig.30:
1.
Center cover
2.
Hex wrench
3.
Blade
guard
Press the shaft lock to lock the spindle and use the hex
wrench to loosen the hex socket bolt. Then remove the
^A @
j
Fig.31:
1.
Shaft lock
2.
Hex wrench
3.
Hex socket
bolt (left-handed)
4.
Loosen
5.
Tighten
Installing the blade
Mount the blade carefully onto the spindle, making
sure that the direction of the arrow on the surface of the
blade matches the direction of the arrow on the blade
case.
j
Fig.32:
1.
# J
2.
# J
blade
> @^A"
hex socket bolt counterclockwise using the hex wrench
while pressing the shaft lock.
j
Fig.33:
1.
Hex socket bolt
2.
: @
3.
Saw
blade
4.
> @
5.
Spindle
6.
Ring
NOTICE:
> @
install it on the spindle with its protrusion facing away
>@
@J
Return the blade guard and center cover to its original
position. Then tighten the hex bolt clockwise to secure
the center cover. Unlock the stopper pin to release
carriage from the raised position. Lower the handle to
make sure that the blade guard moves properly. Make
sure shaft lock has released spindle before making cut.
WARNING:
Before mounting the blade onto
]
)yX'.%)#%|#:y;)y<()]
#]]
)\Y(()\]('.^
[Y(]
);%#)¡y#(;Y(
Y%):Y<'.]).]Y<y)'y
'.y]#%%);)]|)).]
)'..)(#.]
)Y<])(#.^)y
Use of the incorrect arbor hole ring may result in the
improper mounting of the blade causing blade move-
ment and severe vibration resulting in possible loss
of control during operation and in serious personal
Connecting a vacuum cleaner
When you wish to perform clean cutting operation, con-
nect a Makita vacuum cleaner to the dust nozzle using
a front cuff 24 (optional accessory).
j
Fig.34:
1.
Front cuff 24
2.
Hose
3.
Vacuum cleaner
Dust bag
The use of the dust bag makes cutting operations clean and
dust collection easy. To attach the dust bag, remove the
dust extraction hose on the tool and connect the dust bag.
j
Fig.35:
1.
Dust extraction hose
2.
Dust bag
When the dust bag is about half full, remove the dust
bag from the tool and pull the fastener out. Empty
the dust bag of its contents, tapping it lightly so as to
remove particles adhering to the insides which might
hamper further collection.
j
Fig.36:
1.
Fastener
Securing workpiece
WARNING:
]'y)]()j)%:'jXY(]#.]]Y#%|#:y
y)\<()]
)|Y($X')\)\Y(()\]%:|']
]
)X(YX)(
]:X)Y['y)Y(\(Y|.jY%'.^y]YXX)(y
Failure to
damage to the tool and/or the workpiece.
WARNING:
After a cutting operation do not
raise the blade until it has come to a complete
stop.
The raising of a coasting blade may result in
J A
WARNING:
When cutting a workpiece that
'y%Y.^)(]
#.]
)y<XXY(];#y)Y[]
)y#|]
)
material should be supported the entire length
;):Y.]
)y<XXY(];#y)#.#]]
)y#j)
)'^
]
to keep the material level.
Proper workpiece support
will help avoid blade pinch and possible kickback
J
rely solely on the vertical vise and/or horizontal vise
to secure the workpiece. Thin material tends to sag.
Support workpiece over its entire length to avoid
Z>GZ<#GZ
j
Fig.37:
1.
Support
2.
Turn base
Guide fences
WARNING:
&)[Y()YX)(#]'.^] )]YY%j#$)
y<()] #]] )<XX)([).\)'yy)\<()(j%:
WARNING:
&)[Y();))%\<]]'.^j#$)y<()
]
#].YX#(]Y[]
)]YY%)yX)\'#%%:]
);%#)\Y.-
]#\]y]
)<XX)(#.%Y|)([).\)y|
).[<%%:%Y|-
)('.^#.(#'y'.^]
)
#.%)'.#.:XYy']'Y.#.
while moving the carriage through its full range
of travel.
If the tool or blade makes contact with
the fence this may result in kickback or unexpected
Use upper fences to support the material higher than
the lower fences. Insert the upper fence into the hole on
the lower fence and tighten the clamping screw.
j
Fig.38:
1.
Upper fence
2.
Lower fence
3.
Clamping
screw
4.
# J
Содержание LS1219
