manualshive.com logo in svg

Makita LS1019L, Инструкция по эксплуатации

Поделиться
Скачать
Makita LS1019L Скачать руководство пользователя страница 26

26 ENGLISH

NOTICE:

 

Do not remove the screw which 

secures the lens. If the lens does not come out, 

loosen the screw further. 

NOTICE:

 

Do not use solvents or any petro-

leum-based cleaners on the lens.

Replacing carbon brushes

1

►    

1.

 Limit mark

Remove and check the carbon brushes regularly. 

Replace when they wear down to the limit mark. Keep 

the carbon brushes clean and free to slip in the holders. 

Both carbon brushes should be replaced at the same 

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. 

Take out the worn carbon brushes, insert the new ones 

and secure the brush holder caps.

1

►    

1.

 Brush holder cap

After replacing brushes, plug in the tool and break in 

brushes by running tool with no load for about 10 min-

utes. Then check the tool while running and electric 

brake operation when releasing the switch trigger. If 

the electric brake is not working correctly, have the tool 

repaired by a Makita service center.

After use

After use, wipe off chips and dust adhering to the tool 

with a cloth or the like. Keep the blade guard clean 

according to the directions in the previously covered 

section titled "Blade guard". Lubricate the sliding por-

tions with machine oil to prevent rust.
To maintain product SAFETY and RELIABILITY, 

repairs, any other maintenance or adjustment should 

be performed by Makita Authorized or Factory Service 

Centers, always using Makita replacement parts.

OPTIONAL 

ACCESSORIES

WARNING:

 

These Makita accessories or 

attachments are recommended for use with your 

Makita tool specified in this manual.

 The use of 

any other accessories or attachments may result in 

serious personal injury.

WARNING:

 

Only use the Makita accessory 

or attachment for its stated purpose.

 Misuse of 

an accessory or attachment may result in serious 

personal injury.

If you need any assistance for more details regard-

ing these accessories, ask your local Makita Service 

Center.

• 

Steel & Carbide-tipped saw blades

• 

Vertical vise

• 

Horizontal vise

• 

Crown molding stopper set

• 

Dust bag

• 

Triangular rule

• 

Hex wrench

• 

Hex wrench (for LS1019L)

NOTE:

 Some items in the list may be included in the 

tool package as standard accessories. They may 

differ from country to country.

Содержание LS1019L





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды