background image

10 ENGLISH

Adjust the blade position by turning the adjusting bolt 

with the hex wrench. The periphery of the blade should 

extend slightly below the top surface of the turn base 

and also comes to the point where the front face of the 

guide fence meets the top surface of the turn base.

1

►    

1.

 Adjusting bolt

1

2

3

►    

1.

 Top surface of turn base 

2.

 Periphery of blade 

3.

 Guide fence

With the tool unplugged, rotate the blade by hand while 

holding the handle all the way down to be sure that 

the blade does not contact any part of the lower base. 

Re-adjust slightly, if necessary.

After adjustment, always return the stopper lever to the 

original position.

WARNING:

 

After installing a new blade and 

with the tool unplugged, always be sure that the 

blade does not contact any part of the lower base 

when the handle is lowered completely.

 If a blade 

makes contact with the base it may cause kickback 

and result in serious personal injury.

Stopper arm

The lower limit position of the blade can be easily 

adjusted with the stopper arm. To adjust it, turn the 

stopper arm in the direction of the arrow as shown in the 

figure. Turn the adjusting screw so that the blade stops 

at the desired position when lowering the handle fully.

1

2

►    

1.

 Stopper arm 

2.

 Adjusting screw

Adjusting the miter angle

CAUTION:

 

After changing the miter angle, 

always secure the turn base by tightening the grip 

firmly.

NOTICE:

 

When turning the turn base, be sure to 

raise the handle fully.

Содержание LS1019L





























Отзывы: