Makita LS1019L страница 25 Скачать руководство пользователя

Страница: 25 / 28

25 ENGLISH

CAUTION:

Never look directly into the laser

beam.

Direct eye exposure to the beam could cause

serious damage to your eyes.

NOTICE:

Check the position of laser line regu-

larly for accuracy.

NOTICE:

Beware that impacts to the tool.

It may

cause the laser line to be misaligned or may cause

damage to the laser, shortening its life.

NOTICE:

Have the tool repaired by a Makita

authorized service center for any failure on the

laser unit.

The movable range of laser line is decided by the range

adjustment screws on both sides. Perform following

procedures to alter the laser line position.

Unplug the tool.

Draw a cutting line on the workpiece and place it

on the turn base. At this time, do not secure the work-

piece with a vise or similar securing device.

Lower the handle and align the cutting line with

the saw blade.

Return the handle to the original position and

secure the workpiece with the vertical vise so that the

workpiece does not move from the position you have

determined.

Plug in the tool and turn on the laser switch.

Loosen the adjusting screw. To move the laser line

away from the blade, turn the range adjustment screws

counterclockwise. To move the laser line close to the

blade, turn the range adjustment screw clockwise.

Adjusting the laser line on the left side of the blade

►

Adjusting screw

Range adjustment screw

Hex wrench

Laser line

Saw blade

Adjusting the laser line on the right side of the

blade

►

Adjusting screw

Range adjustment screw

Hex wrench

Laser line

Saw blade

Slide the adjusting screw to the position that the

laser line comes onto the cutting line and then tighten.

NOTE:

The movable range of laser line is factory

adjusted within 1 mm (0.04") from the side surface

of blade.

Cleaning the laser light lens

For model LS1019L only

The laser light becomes hard to see as the lens for

the laser light gets dirty. Clean the lens for laser light

periodically.

►

Screw

Lens

Unplug the tool. Loosen the screw and pull out the lens.

Clean the lens gently with a damp soft cloth.

Содержание LS1019L





























Результаты поиска

Содержание LS1019L

Отзывы:

Похожие инструкции для LS1019L

Бренды по названию

Популярные бренды

Makita LS1019L, Инструкция по эксплуатации

Результаты поиска

Содержание LS1019L

Отзывы:

Похожие инструкции для LS1019L

Бренды по названию

Популярные бренды