background image

13 ENGLISH

To prevent the switch trigger from being accidentally pulled, a lock-off 

button is provided. To start the tool, press in the lock-off button and 

pull the switch trigger. Release the switch trigger to stop.

A hole is provided in the switch trigger for insertion of a 

padlock to lock the tool off.

WARNING:

 

Do not use a lock with a shank or cable 

any smaller than 6.35 mm (1/4") in diameter.

 A smaller shank or 

cable may not properly lock the tool in the off position and uninten-

tional operation may occur resulting in serious personal injury.

Electronic function

Constant speed control

The tool is provided with an electronic speed control which helps 

maintain a constant blade rotation speed even under load. A 

constant blade rotation speed will result in a very smooth cut.

Soft start feature

This function allows the smooth start-up of the tool by 

limiting the start-up torque.

Laser beam action

For model LS1019L only

CAUTION:

 

Never look into the laser beam.

 

Direct laser beam may injure your eyes.

To turn on the laser beam, press the upper position (I) of the switch. 

To turn off the laser beam, press the lower position (0) of the switch

1

►    

1.

 Switch for laser

Laser line can be shifted to either the left or right side of 

the saw blade by turning the adjusting screw as follows.

1

►    

1.

 Adjusting screw

1.

  Loosen the adjusting screw by turning it 

counterclockwise.

2.

  With the adjusting screw loosened, slide the 

adjusting screw to the right or left as far as it goes.

3.

  Tighten the adjusting screw firmly at the position 

where it stops sliding.

NOTE:

 

Laser line is factory adjusted so that it is positioned within 

1 mm from the side surface of the blade (cutting position).

NOTE:

 When laser line appears dim and hard to see 

because of direct sunlight, relocate the work area to a 

place where there is less direct sunlight.

Aligning the laser line

Align the cutting line on your workpiece with the laser line.

A

B

A) When you want to obtain the correct size on the left side of 

workpiece, shift the laser line to the left of the blade.

B) When you want to obtain the correct size on the right side 

of workpiece, shift the laser line to the right of the blade.

NOTE:

 Use wood facing against the guide fence 

when aligning the cutting line with the laser line at the 

side of guide fence in compound cutting (bevel angle 

45° and miter angle right 45°).

ASSEMBLY

WARNING:

 

Always be sure that the tool is 

switched off and unplugged before working on 

the tool.

 Failure to switch off and unplug the tool may 

result in serious personal injury.

Содержание LS1019L





























Отзывы: