8
ENG901-1
•
The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
•
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
•
The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
•
Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
ENH009-1
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Table Top Miter Saw
Model No./ Type: LH1040, LH1040F
are of series production and
Conforms to the following European Directives:
98/37/EC until 28th December 2009 and then with
2006/42/EC from 29th December 2009
And are manufactured in accordance with the following
standards or standardised documents:
EN61029
Certificate of adequacy of the technical file with respect
to 98/37/EC and 2006/42/EC having been obtained
from:
Intertek SEMKO AB,
Torshamnsgatan 43,
Box 1103, SE-164 22 Kista, Sweden
Identification No. 0413
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd,
Michigan, Drive, Tongwell,
Milton Keynes, MK15 8JD, England
30
t
h J
a
nu
ar
y 2009
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
GEA010-1
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions.
Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for
future reference.
ENB088-2
ADDITIONAL SAFETY RULES
FOR TOOL
FOR BOTH MITER SAW MOGE AND TABLE SAW
(BENCH SAW) MODE
1.
Wear eye and hearing protection. Other
suitable personal protective equipment should
be worn.
2.
NEVER wear gloves during operation except
for replacing saw blades or handling rough
material before operation.
3.
Keep the floor area around the tool level well
maintained and free of loose materials e.g.
chips and cut-offs.
4.
Do not operate saw without guards and riving
knife in place. Check blade guards for proper
closing before each use. Do not operate saw if
blade guards do not move freely and close
instantly. Never clamp or tie the blade guards
into the open position. Any irregular operation
of the blade guards should be corrected
immediately.
5.
Clean and be careful not to damage the
spindle, flanges (especially the installing
surface) and hex bolt before or when installing
the blade. Damage to these parts could result
in blade breakage. Poor installation may cause
vibration/wobbling or slippage of the blade.
Use only flanges specified for this tool.
6.
Check the blade carefully for cracks or
damage before operation. Do not use saw
blade which are damaged or deformed.
7.
Use only saw blades recommended by the
manufacturer and which conform to EN847-1,
and observe that the riving knife must not be
thicker than the width of the cut by the saw
blade and not thinner than the body of the
blade.
8.
Always use accessories recommended in this
manual. Use of improper accessories such as
abrasive cut-off wheels may cause an injury.
9.
Select the correct saw blade for the material to
be cut.
Содержание LH1040
