background image

14

Refueling

WARNING: Shut off the engine before refueling, keep away from 

Loosen the tank cap a little to release the tank pressure.

 

Detach the tank cap, and refuel, discharging air by tilting the fuel tank so that 

 

tank. 

Wipe the outside of the tank cap to prevent debris from entering into the fuel 

 

tank. 

After refueling, securely tighten the tank cap. 

 

The tank cap wears out in course of time. Replace it every two to three years.

Fuel tank cap

Fuel upper limit

Fuel tank

Note

Do not replace oil with the engine in a tilted position.

Wipe with a rag any spilled oil immediately. 

 

REFUELING

Handling of fuel

ventilated room or in the open air. Never inhale fuel vapor, and keep fuel away from you. If you touch fuel repeatedly or for a long time, the 
skin becomes dry, which may cause skin disease or allergy. If fuel enters into the eye, clean the eye with fresh water. If your eye remains still 
irritated, consult your doctor.

Storage period of fuel

Fuel should be used within a period of 4 weeks, even if it is kept in a special container in a well-ventilated and shaded area.
Otherwise, fuel may deteriorate in one day.

STORAGE OF MACHINE AND REFILL TANK

Keep the machine and tank at a cool place free from direct sunshine.

 

Never keep the fuel in a car.

 

Fuel

The engine is a four-stroke engine. Be sure to use an unleaded automobile gasoline 87 or higher octane ((R+M)/2). It may contain no more than 
10% alcohol (E-10).

Points for fuel

Never use a gasoline mixture which contains engine oil. Otherwise, it will cause excessive carbon accumulation or mechanical troubles. 

 

Use of deteriorated oil will cause irregular start-up. 

 

Содержание EM4351UH





























Отзывы: