background image

25

Fuel pipe

REPLACEMENT OF FUEL PIPE

CAUTION: INFLAMMABLES STRICTLY PROHIBITED

Interval of Cleaning and Inspection: Daily (every 10 operating hours)
Replacement: Annually (every 200 operating hours)

Replace the fuel pipe every year, regardless of operating frequency. Fuel 

If any leakage is detected during inspection, replace the fuel pipe immediately.

INSPECTION OF BOLTS, NUTS AND SCREWS

Retighten loose bolts, nuts, etc.

 

Check the fuel cap and oil cap for tightness. Check for fuel and oil leakage.

 

Replace damaged parts with new ones for safety operation.

 

CLEANING OF PARTS

Always keep the engine clean by wiping down with a cloth rag.

 

 

cause piston seizure.

REPLACEMENT OF GASKETS AND PACKINGS

Replace gaskets and packings if the engine is disassembled.
Any maintenance or adjustment work that is not included and described in this manual is only to be performed by Authorized Service Agents.

WARNING:

The engine is still hot just after stopping engine. When draining the fuel, allow 

DANGER: 

 When the machine is kept out of operation for a long time, drain all fuel from the fuel 
tank and carburetor, and keep it at a dry and clean place.

Drain fuel from the fuel tank and carburetor according to the following 

 

procedure:
1)  Remove the fuel tank cap, and drain fuel completely.
 

If there is any foreign matter remaining in the fuel tank, remove it 
completely.

3)  Push the primer pump until fuel is drained from there, and drain fuel 

coming into the fuel tank.

5)  Then, continue to operate the engine until it stops.

Remove the spark plug, and drip several drops of engine oil through the 

 

spark plug hole.

Gently pull the starter handle so that engine oil will spread over the engine, 

 

and attach the spark plug.

Attach the cover to the metal blade.

 

In general, store the machine in horizontal position, or if it is not possible, 

 

place the machine as the cutting tool comes below the engine. Pay full 
attention how to store the machine to prevent the machine from falling. 
Otherwise it may result in personal injury.  

Keep the drained fuel in a special container in a well-ventilated shade.

 

STORAGE

Attention after long-time storage

Before startup after long-time shutdown, be sure to replace oil (refer to P 22). Oil will deteriorate while the machine is kept out of 

 

operation.

Содержание EM4351UH





























Отзывы: