background image

12

Be sure to use genuine MAKITA metal blades or nylon 
cutting head.

The metal blade must be well polished, free of cracks or breakage. If the 

 

metal blade hits against a stone during operation, stop the engine and check 
the blade immediately.

Polish or replace the metal blade every three hours of operation.

 

If the nylon cutting head hits against a stone during operation, stop the 

 

engine and check the nylon cutting head immediately.

CAUTION:  The appropriate protector must always be installed, for your own 

safety and in order to comply with accident-prevention regulations.

 

Operation of the equipment without the guard being in place is not 
permitted.

 

The outside diameter of the cutter blade must be 300 mm (12”) 
or less. Never use any blades exceeding 300 mm (12”) in outside 
diameter.

Turn the machine upside down, and you can replace the metal blade or nylon 
cutting head easily.

Insert the hex wrench through the hole in the gear case and rotate the 

 

receiver washer (4) until it is locked with the hex wrench.

Loosen the nut (1) (left-hand thread) with the socket wrench and remove the 

 

nut (1), cup (2), and clamp washer (3).

(4)

(3)

(2)

(1)

(4)

(3)

(2)

(1)

Rotation

Hex wrench

MOUNTING OF METAL BLADE OR NYLON CUTTING HEAD

Mounting of metal blade with the hex wrench still in place

Mount the metal blade onto the shaft so that the guide of the receiver washer 

 

(2), and secure the metal blade with the nut (1).
[Tightening torque: 20 - 30 N-m]

NOTE:  Always wear gloves when handling the metal blade.
NOTE:   The metal blade-fastening nut (with spring washer) is a consumable 

part. If there appears any wear or deformation on the spring washer, 
replace the nut.

Mounting of nylon cutting head

The clamp washer (3), cup (2), and nut (1) are not necessary for mounting 

 

the nylon cutting head. The nylon cutting head should go on top of the 
receiver washer (4).

Insert the hex wrench through the hole in the gear case and rotate the 

 

receiver washer (4) until it is locked with the hex wrench.

Then screw the nylon cutting head onto the shaft by turning it counter-

 

clockwise.

Remove the hex wrench.

 

Hex wrench

Loosen

Tighten

Hex wrench

Содержание EM4351UH





























Отзывы: