![background image](http://html1.mh-extra.com/html/makita/cg100dsax/cg100dsax_instruction-manual_3895350010.webp)
10 ENGLISH
Installing or removing the rod and piston
1.
Insert the rod from the rear side of the tool with its
teeth facing down.
►
Fig.13:
1.
Long rod or black rod
NOTICE:
For 600 ml size holder, use the long
rod. For 800 ml size holder, use the black rod.
2.
Attach the piston with the screw.
►
Fig.14:
1.
Screw
2.
Piston
3.
Long rod or black rod
To remove the rod and piston, follow the installation
procedure in reverse.
Installing or removing 600 ml or 800
ml size holder
CAUTION:
Secure the holder to the holder
joint firmly. Otherwise the holder may come off
during operation and may cause an injury.
To install the holder, turn it clockwise firmly until it stops
while holding the holder joint.
►
Fig.15:
1.
Holder
To remove the holder, follow the installation procedure
in reverse.
OPERATION
Using cartridge
Preparing cartridge for use
1.
Cut the tip of the cartridge nozzle so that the suit-
able amount of caulking material is fed.
►
Fig.16:
1.
Nozzle
2.
Make a hole on the protective film with the tip of
the nozzle.
►
Fig.17:
1.
Nozzle
3.
Attach the nozzle to the cartridge.
NOTICE:
Be sure to check the cartridge for
damage before installation. Using the damaged
cartridge may cause malfunction.
NOTICE:
When reusing the partially used car-
tridge, be sure to remove the solid caulking mate-
rial before the installation.
Installing cartridge to 300 ml size
holder
NOTICE:
Make sure that piston A is attached
to the rod. Do not use other type of piston for
cartridge.
1.
Pull the rod handle backward slowly until it stops.
►
Fig.18:
1.
Rod handle
2.
Insert the cartridge into the holder as shown in the
figure.
►
Fig.19
3.
Push the rod gently until the piston touches the
bottom of cartridge.
To remove the cartridge, follow the installation proce-
dure in reverse.
Installing cartridge to 600 ml or 800
ml size holder
NOTICE:
Make sure that piston A (for 600 ml
size holder) or piston D (for 800 ml size holder) is
attached to the rod. Do not use other type of pis-
ton for cartridge.
1.
Remove the holder cap from the holder, and then
pull the rod handle backward slowly until it stops.
►
Fig.20:
1.
Holder cap
2.
Rod handle
2.
Insert the cartridge into the holder.
►
Fig.21:
1.
Holder
3.
Attach the holder cap by turning it firmly while
holding the holder.
►
Fig.22:
1.
Holder cap
2.
Holder
4.
Push the rod gently until the piston touches the
bottom of cartridge.
To remove the cartridge, follow the installation proce-
dure in reverse.
Using film type package
Preparing package for use
Cut off the tip of the package.
►
Fig.23
NOTICE:
Be sure to check the package for dam-
age before installation. Using the damaged pack-
age may cause malfunction.
Installing film type package to 600 ml
or 800 ml size holder
NOTICE:
Make sure that piston B (for 600 ml
size holder) or piston E (for 800 ml size holder) is
attached to the rod. Do not use other type of pis-
ton for film type package.
1.
Remove the holder cap, nozzle, and rubber ring
from the holder.
►
Fig.24:
1.
Holder cap
2.
Nozzle
3.
Rubber ring
4.
Holder
2.
Pull the rod handle backward slowly until it stops.
3.
Insert the package into the holder.
►
Fig.25:
1.
Holder
4.
Attach the rubber ring, nozzle, and holder cap by
turning the holder cap firmly.
►
Fig.26:
1.
Holder cap
2.
Nozzle
3.
Rubber ring
4.
Holder
5.
Push the rod gently until the piston touches the
package.
To remove the package, remove the holder cap, nozzle,
rubber ring, and then push the rod handle forward until
it stops.
Содержание CG100DSAX
Страница 2: ...1 2 3 Fig 1 1 2 Fig 2 A B 1 2 Fig 3 1 Fig 4 1 Fig 5 1 Fig 6 1 2 3 Fig 7 1 Fig 8 2 ...
Страница 3: ...1 2 3 Fig 9 1 Fig 10 1 2 3 Fig 11 1 2 Fig 12 1 Fig 13 1 2 3 Fig 14 1 Fig 15 1 Fig 16 3 ...
Страница 4: ...1 Fig 17 1 Fig 18 Fig 19 1 2 Fig 20 1 Fig 21 1 2 Fig 22 Fig 23 1 4 2 3 Fig 24 4 ...
Страница 5: ...1 Fig 25 1 4 2 3 Fig 26 1 4 2 3 Fig 27 1 Fig 28 1 4 2 3 Fig 29 5 ...