background image

PROPELL

BA

TTERI

ARMERING

When the drone is armed* and the propellers are 
mounted.

you must have at least 2 meters safety distance to 
the nearest person.

*Arming: The drone is activated and the propellers 
can spin. Characteristics: Red light on control card, 
it says "ARMED" in the display.

The drone battery (LiPo), can develop heat and toxic 
fumes if it is severely damaged. It the batteri suddenly 
inflates or starts to extract smoke, get the battery outside 
the premises,  and away from people as quickly as 
possible. 

Have a plan for this in advance.

Rule 1:

Rule 2:

3

Propeller hazard 

The propellers rotate at up to 28,000 rpm. minute. 
Show respect for the forces and damage potential of 
the propellers when the drone has battery connected.

Keep the required safety distance when the drone is 
armed.

Aviation rules 

When flying outdoors, make sure to follow local drone 
rules. Keep a safe distance so as not to endanger other 
people. 

It is not recommended to fly this drone higher than the 
roof of the nearest building and no more than 30 
meters away from yourself. This will help you retain 
control of the drone.

Safety

Содержание MD2 Dronekit

























Отзывы: