Majestic DBDV36PLATIN страница 47 Скачать руководство пользователя

Страница: 47 / 74

Majestic • DBDV36PLATIN, DBDV36PLATIL, DBDV42PLATIN, DBDV42PLATIL Installation Manual • 2454-980 Rev. F • 5/17

A. Fuel Conversion

• Make sure the appliance is compatible with available gas

types.

• Conversions must be made by a qualified service

technician using Hearth & Home Technologies specified

and approved parts.

B. Gas Pressure

• Optimum appliance performance requires proper input

pressures.

• Gas line sizing requirements will be determined in ANSI

Z223.1 National Fuel Gas Code in the USA and CAN/

CGA B149 in Canada.

• Pressure requirements are:

C. Gas Connection

• Refer to Appliance Dimension diagram in Section 3 for

location of gas line access in appliance.

• Gas line may be run through knockout(s) provided.

• The gap between supply piping and gas access hole

may be caulked with caulk with a minimum of 300

ºF continuous exposure rating or stuffed with non-

combustible, unfaced insulation to prevent cold air

infiltration.

• Ensure that gas line does not come in contact with outer

wrap of the appliance. Follow local codes.

• Pipe incoming gas line into valve compartment.
• Connect incoming gas line to the 1/2 in. (13 mm)

connection on manual shutoff valve.

WARNING! Risk of Fire or Explosion!

Support control

when attaching pipe to prevent bending gas line.

• A small amount of air will be in the gas supply lines.

WARNING! Risk of Fire or Explosion!

Gas build-up

during line purge could ignite.
• Purge should be performed by qualified service

technician.

• Ensure adequate ventilation.
• Ensure there are no ignition sources such as sparks or

open flames.

Light the appliance. It will take a short time for air to purge

from lines. When purging is complete the appliance will

light and operate normally.

WARNING! Risk of Fire, Explosion or Asphyxiation!

Check all fittings and connections with a non-corrosive

commercially available leak-check solution.

DO NOT

use

open flame. Fittings and connections could have loos

ened during shipping and handling.

WARNING! Risk of Fire! DO NOT

change valve settings.

This valve has been preset at the factory.

WARNING! Risk of Fire or Explosion!

High pressure

will damage valve. Low pressure could cause explosion.

• Verify inlet pressures. Verify minimum pressures when

other household gas appliances are operating.

• Install regulator upstream of valve if line pressure is

greater than 1/2 psig.

Gas Information

Gas Pressure

Natural Gas

Propane

Minimum inlet pressure

5.0 in. w.c.

11.0 in. w.c.

Maximum inlet pressure

10.0 in. w.c.

13.0 in. w.c.

Manifold pressure

3.5 in. w.c.

10.0 in. w.c.

Note:

Have the gas supply line installed in accordance with

local codes, if any. If not, follow ANSI 223.1. Installation

should be done by a qualified installer approved and/or

licensed as required by the locality. (In the Commonwealth

of Massachusetts installation must be performed by a

licensed plumber or gas fitter).

Note:

A listed (and Commonwealth of Massachusetts ap-

proved) 1/2 in. (13 mm) T-handle manual shut-off valve

and flexible gas connector are connected to the 1/2 in. (13

mm) control valve inlet.

• If substituting for these components, please consult

local codes for compliance.

Fire Risk.
Explosion Hazard.
High pressure will damage valve.
• Disconnect gas supply piping BEFORE

pressure testing gas line at test pressures

above 1/2 psig.

• Close the manual shutoff valve BEFORE

pressure testing gas line at test pressures

equal to or less than 1/2 psig.

WARNING

D. High Altitude Installations

NOTICE:

If the heating value of the gas has been reduced,

these rules do not apply. Check with your local gas utility

or authorities having jurisdiction.

When installing above 2000 feet elevation:
• In the USA: Reduce input rate 4% for each 1000 feet

above 2000 feet.

• In CANADA: Input ratings are certified without a

reduction of input rate for elevations up to 4500 feet

(1370 m)above sea level. Please consult provincial and/

or local authorities having jurisdiction for installations at

elevations above 4500 feet (1370 m).

Check with your local gas utility to determine proper

orifice size.

Содержание DBDV36PLATIN











































































Результаты поиска

Содержание DBDV36PLATIN

Отзывы:

Похожие инструкции для DBDV36PLATIN

Бренды по названию

Популярные бренды

Majestic DBDV36PLATIN, Руководство по установке

Результаты поиска

Содержание DBDV36PLATIN

Отзывы:

Похожие инструкции для DBDV36PLATIN

Бренды по названию

Популярные бренды