Majestic DBDV36PLATIN страница 30 Скачать руководство пользователя

Страница: 30 / 74

Majestic • DBDV36PLATIN, DBDV36PLATIL, DBDV42PLATIN, DBDV42PLATIL Installation Manual • 2454-980 Rev. F • 5/17

EXHAUST VENT PIPE

INLET AIR VENT PIPE

Figure 4.25. Coaxial/Colinear Appliance Connector

OUTSIDE FACE OF

FIREPLACE

TOP OF FIREPLACE

OPENING

SHADED AREA DEFINED AS

“INSIDE EXISTING MASONRY

FIREPLACE”

3 IN. MIN.

5 IN. MIN.

EXHAUST VENT PIPE

Figure 4.26. Existing Fireplace DV-46DVA-GCL

Clearance Requirements

Clearances to Combustibles:

Refer to Section 5 for clearances to the appliance, man-

tel, mantel legs and wall projection.
Refer to Section 8 for pipe clearances to combustibles.

Termination Cap

For installation of termination cap see minimum vent

heights for various pitched roofs. See Section 6 of appli

ance owner’s manual.

Flue Damper

Fully lock the solid fuel fireplace’s flue damper in the open

position, OR completely remove it.

Venting Components

The LINK-DV30B is approved for use with the coaxial/co

linear venting application. The LINK-DV30B kit includes:
• Two 30 feet sections of flexible vent pipe (3 inches Ø).

One section is used to draw combustion air and the other

section is used to expel exhaust gases.

• One vertical term

ination cap.

WARNING! Risk of Fire!

Coaxial to colinear venting con-

figuration may only be used in existing non-combustible

chimney. Installation in any other venting application

could cause fire.

Prior to installing the gas appliance:

• Have the chimney and adjacent structure inspected

and cleaned by qualified professionals. Hearth & Home

Technologies recommends that NFI or CSIA certified

professionals, or technicians under the direction of certi-

fied professionals, conduct a minimum of a NFPA 211

Level 2 inspection of the chimney.

• Replace component parts of the chimney and fireplace

as specified by the professionals.

• Ensure all joints are properly engaged and the chimney

is properly secured.

Coaxial to Colinear Venting

The coaxial to colinear adapter (DV-46DVA-GCL) is ap

proved for installations into solid fuel masonry or factory

built fireplaces that have been installed in accordance

with the National, Provincial, State and local building

codes. The DV-46DVA-GCL must be recessed into exist

ing masonry fireplace. See Table 4.2, and Figures 4.25

and 4.26.

Table 4.2.

CLEARANCE TO COMBUSTIBLES REQUIREMENTS

DV-46DVA-GCL

3 IN.

Exhaust Vent Pipe

5 IN.

CAUTION! DO NOT

use any flue restrictor when vent

ing with the DV-46DVA-GCL adapter and LINK-DV30B

kit.

This may result in poor flame appearance, sooting,

pilot malfunction, or overheating.

Содержание DBDV36PLATIN











































































Результаты поиска

Содержание DBDV36PLATIN

Отзывы:

Похожие инструкции для DBDV36PLATIN

Бренды по названию

Популярные бренды

Majestic DBDV36PLATIN, Руководство по установке

Результаты поиска

Содержание DBDV36PLATIN

Отзывы:

Похожие инструкции для DBDV36PLATIN

Бренды по названию

Популярные бренды