background image

DVB Series Direct Vent Gas Fireplace

48

54D0701

FINAl INstAllAtIoN

RocK Wool plAceMeNt

1.  Place rock wool on burner to provide glowing embers. 

For best results, pull the rock wool apart into pieces 
the size of a dime or smaller. 

2.  Distribute one layer of rock wool to cover the  burner. 

Figure 60

3.  Place the logs on the burner. Refer to 

Log Placement 

below. Light unit and after 15 minutes, check burner 
flame and glow. Refer to 

Burner Flame

, Page 49. 

If the flame is blue and only in the center, turn off unit 
and  let  cool. After  unit  cools,  remove  logs.  If  the  back 
holes are clear, add more rock wool to the center of the 
burner. Replace logs and check flame again. Save left 
over rock wool to refresh when cleaning later. Too much 
rock  wool  can  disturb  the  flame  and  cause  sooting  on 
the glass or logs. 

FP2105
BDV base

Figure 60 - Placement of 
Rock Wool on Burner

Cover with 
Rock Wool 

Burner 

FP2105

W

ARNING

Do not use the entire bag of rock wool to 
cover the burner. this could cause the flame 
to burn poorly and may lead to sooting.

loG plAceMeNt

1.  Place rear log (#1) on grate assembly. Log should 

rest firmly on the two log mounting pins on the 
bars. 

Figure 61

2.  Place bottom left log (#2) on grate. Rest the back 

side of the log in the flat area of the rear log. 

Figure 

61 

3.  Place  bottom  right  log  (#3)  on  grate.  Rest  the 

back side of the log in the flat area of the rear log. 

Figure 61 

4.  Place the top log (#4) on the rear log. Nest the 

forked end of the  top left log into the fork or the 
rear log. Rest the narrow end of the top on the 
vertical grate bar.

 Figure 61 

lAVA RocK AND eMBeRs plAceMeNt

Sprinkle lava rock on the floor of the inner combustion 
chamber. Evenly distribute the rock. Do not pile the lava 
rock up in front of grate. Do not place lava rock on the 
burner. If desired, purchase optional embers to decorate 
the floor of the fireplace. 

LG607
DVB logs

Top Log #4

Bottom Left 
Log #2

Bottom 
Right 
Log #3

Log Mouting 
Pins

Flat Areas

Rear Log 
#1

Left Verti-
cal Grate 
Bar

Center Vertical 
Grate Bar

Right Vertical 
Grate Bar

LG607

Figure 61 -
Log Placement 
(300DVB & 400DVB Shown)

W

ARNING

Do  not  sprinkle  the  lava  rock  or  ember 
chunks on top of the burner. this may cause 
potential sooting, glass breakage and a fire 
hazard

Содержание 400DVB





































































Отзывы: