background image

28

10.0 Installation

© Baxi Heating UK Ltd 2011

10.3

Fitting The Boiler

1. Lift the boiler using the Lifting Points as shown by the
shaded areas (Fig. 43). The boiler should be lifted by TWO
PEOPLE. Engage the slots at the top rear of the boiler on the
wall plate (Fig. 42) (see 

Safe Manual Handling

page 5).

2. Ease the boiler forwards and remove the sealing caps from
the boiler connections (Fig 43).

NOTE:

A small amount of water may drain from the

boiler once the caps are removed.

3. 

Insert the sealing washers between the valves and pipes

on the wall plate and the boiler connections. The rubber
washers must be used on the gas connection.

4. Tighten all the connections.

10.4

Fitting the Pressure Relief  Discharge Pipe 
(Fig. 44)

1. Remove the discharge pipe from the kit. 

2. Determine the routing of the discharge pipe in the vicinity
of the boiler. Make up as much of the pipework as is
practical, including the discharge pipe supplied.

3. The pipework must be at least 15mm diameter and run
continuously downwards to a discharge point outside the
building. See section 6.7 for further details.

4. Utilising one of the sealing washers, connect the discharge
pipe to the adaptor and tighten the nut.

5. Complete the discharge pipework and route it to the
outside discharge point.

IMPORTANT:

Make all soldered joints before connecting

to the pressure relief valve.

10.5

Condensate Drain 

(see Section 7.7)

1. Connect the condensate drain to the trap outlet pipe.

Ensure the discharge of condensate complies with any
national or local regulations in force (see British Gas
“Guidance Notes for the Installation of Domestic Gas
Condensing Boilers”.

2. The connection will accept 21.5mm (

3

/

4

in) plastic overflow

pipe which should generally discharge internally into the
household drainage system. If this is not possible, discharge
into an outside drain is acceptable.

Fig. 44

Pressure Relief Valve

Wall Plate

Discharge Pipe

Suggested Lifting Points

shown as shaded area

Fig. 43

Remove Sealing Caps

from under the Boiler

Supplied by HeatingSpares247.com

Содержание System 28 Eco

























































Отзывы: