background image

© MAHLE 

10  |  NTF-515B  |  Product description

en

2.5 

Unit features

2.5.1  Nitrogen purity selection

 

t

The  NTF-515B  allows  the  operator  to  select  the  desirable 
purity of generated Nitrogen. Purity selector is located in the 
lower left corner of the unit's rear panel.

To adjust the purity setting:

1. 

Turn knob to desired purity setting.

2. 

If switching from 95% to 98% purity, drain tank of all pressure 
and allow tank to generate fresh Nitrogen.

 

m

Nitrogen tank regeneration time will be about twice as long 
if 98% purity is selected.

Fig. 5: 

Purity selector valve

2.5.2  Air chucks

 

t

To connect air chuck to valve stem, press down on the silver 
clip, push air chuck onto valve stem until tight, and release 
silver clip.

 

t

To remove the air chuck from the valve stem, press down on 
the silver clip and pull off of valve stem.

Fig. 6: 

Air chuck

2.4 

User interface

2.4.1  Selection and function keys

Keys

Function

+

Use this button to adjust the desired value higher.

-

Use this button to adjust the desired value lower.

START

Press and hold button to begin a Nitrogen purge cycle or 

just press once for a Top-Off cycle.

N

2

Press this button from the startup screen to adjust the OPS 

setting and the number of purge cycles prior to starting 

service.

2.4.2  Input selection

 

t

The buttons on the NTF-515B are touch sensitive. Touch black 
dot on the control panel under the text of the desired selection.

Fig. 4: 

Selecting button on control panel

2.4.3  Value adjustment

To adjust the target inflation value, simply press the 

+

 or 

-

 but-

tons. The value in the upper screen will adjust accordingly.

Содержание NitroPRO NTF-515B





















Отзывы: