background image

Always disconnect the negative terminal first when removing the battery and  
always connect the positive terminal first when fitting the battery.

 

When connecting the battery leads make sure not to reverse the polarity.

 

Quick charging will reduce battery life.

 

Disconnect the terminals prior to charging the battery to avoid damage to the  
circuit and electrical instruments.  

Caution 

 FAN BELT ADJUSTMENT  

1.Loosen the alternator pivot bolt. 

2.Move the alternator in order to increase or  

  decrease the belt tension. Tighten the alternator  

  pivot bolt and the link bolt to 22 N.m (16 lb ft). 

 SERVICING THE AIR CLEANER 

 Cleaning the Air Cleaner Dust Valve 

Check that the dust valve is not blocked. 

Inspect the rubber flaps for cuts and nicks and check that 

the rubber is not perished. Renew if necessary. 

To remove dust from the dust valve, squeeze it between 

thumb and fingers. Wipe around the dust valve to remove 

dust collected on the outside. 

 Cleaning/Changing the Element

 

Release the two clips on the air cleaner end cover  

and remove the element. 

Remove dust by blowing compressed air through the element. 

Check the element for damage, if necessary, change the elements. 

Check all hoses for condition and tightness. 

 

 

Never beat the element on a stone or concrete floor/wall to clean it.  

Check all connections and hoses especially on the clean side of the air cleaner to 
ensure no dusty air can enter the engine.

 

Check the element for flaws by putting a light inside the element.

 

When reassembling, make sure all surfaces seal correctly to keep dust out.

 

When working in dusty conditions, increase the service frequency.  

  Replace the element after cleaning it 5 times or if it is damaged.  

Important 

65 

Содержание eMax 22L HST





























































































Отзывы: