Mahindra eMax 22L HST Скачать руководство пользователя

Страница: 35 / 92

►

TRACTOR CONTROLS

►

SPEED CONTROL PEDAL

The Speed Control Pedal is located in the RHS of the Operator floor.

Depress the forward speed control pedal to move forward.

Depress the reverse speed control pedal to move backward.

The speed control pedal will return to neutral position

and the tractor will stop when the speed control pedal is released.

►

THROTTLE LEVER (HAND THROTTLE)

The hand operated throttle lever is located on the RHS

of the dash cover.

To increase the engine speed, pull the lever downward.

To decrease the engine speed, push the lever upward.

The Lever can be left in any position between idle and maximum

as required.

Steering Wheel

Brake Pedal

4WD Shift Lever

Rear/Mid PTO Lever

Sub Gear Lever

Forward/Reverse
Speed Control pedal

Position Lever

Throttle Lever

Содержание eMax 22L HST





























































































Результаты поиска

Содержание eMax 22L HST

Отзывы:

Похожие инструкции для eMax 22L HST

Бренды по названию

Популярные бренды

Mahindra eMax 22L HST, Руководство оператора

Результаты поиска

Содержание eMax 22L HST

Отзывы:

Похожие инструкции для eMax 22L HST

Бренды по названию

Популярные бренды