Mahindra eMax 22L HST Скачать руководство пользователя

Страница: 33 / 92

►

WARNING LIGHTS

Charge Lamp

This light will go off as soon as the engine starts to run to indicate that the alternator is
charging. (Please note, as a broken fan belt can cause the light to come on, please stop the
engine as overheating can occur if not rectified immediately)

Oil Pressure Lamp

Will go out as soon as the engine starts if the oil pressure is correct.

If it comes on while the engine is running, stop the engine and get expert advice

PTO Monitor Lamp

Shows the revolution of the PTO.

Refer to Monitor Lamp on page 32.

High Beam Lamp

is operated on the combination switch.

Low Beam Lamp

is operated on the combination switch.

Glow Signal Lamp

indicates preheating.

Fuel Level

: If it comes on while the engine is running, fill the tank with fuel.

Содержание eMax 22L HST





























































































Результаты поиска

Содержание eMax 22L HST

Отзывы:

Похожие инструкции для eMax 22L HST

Бренды по названию

Популярные бренды

Mahindra eMax 22L HST, Руководство оператора

Результаты поиска

Содержание eMax 22L HST

Отзывы:

Похожие инструкции для eMax 22L HST

Бренды по названию

Популярные бренды