MAGUIRE Weigh Scale Blender, Установка, эксплуатация и обслуживание

Страница: 55 / 141

M A G U I R E P R O D U C T S , I N C .
55
W E I G H S C A L E B L E N D E R

Press (*,5,7) to allow automatic switch over to a full drum when the current drum of color runs out. When
function is off, display will say
LIQ OFF . Press * to toggle to COL 04 . When display says COL 04 , the
color setting applies to output 04 only, the standard COLOR output. When display says COL 04
→
07 , this
means that output 04 is the starting output, and when no weight is detected after a dispense, the controller
will alarm, then the output switches to output 07. The "07" is determined by the parameter (LIQ 10007).
You can change the secondary output by changing the parameter.
If output 07 is also empty, the output switches back to 04. See parameter (LIQ 10007) for more information.
When finished, press
Exit to save changes, then press Exit again to exit out of Programming Mode.
WSB COMMUNICATIONS
– View the Blender’s Ethernet IP Address, Subnet and Gateway
Note: this star function is available in controller software versions ending in /N
Press (*,6,0) to view the WSB’s Ethernet IP Address, Subnet and Gateway. If the WSB is configured to
obtain an IP automatically (DHCP) through *65, then the IP, Subnet will be whatever was assigned to the
controller by a DHCP Server on your network. If the IP address was configured manually, this will be
whatever was entered using *65. Press the * key to toggle through IP, Subnet and Gateway. Press EXIT
when done.
WSB COMMUNICATIONS
– View the Blender’s Ethernet MAC Address
Note: this star function is available in controller software versions ending in /N
Press (*,6,2) to
view the WSB’s Ethernet MAC Address. View Only.
WSB COMMUNICATIONS
– Set the Blender TCP/IP Settings (IP Address, Subnet Gateway)
Note: this star function is available in controller software versions ending in /N
Press (*,6,5) to configure Ethernet IP Address Settings. Under Static IP, you may assign a static IP
Address, Subnet and Gateway.
Press the
CE key to toggle between DHCP and static IP Address.
Note: If you plan to use DHCP be aware that software connecting to the Maguire Controller
typically requires a known IP address that does not change, therefore your DHCP server will most
likely need to maintain the same IP for the controller. To determine the controllers MAC address,
see *62.
Using a Static IP Address - Press the
CE key to toggle between DHCP and static IP Address. When the
display toggles to Static IP, use the keypad to enter the static IP address you wish to assign the controller.
Use leading zeros and press the * key for decimal. After entering the IP, the display will go to Network
Mask (Subnet), the to Default Gateway. After entering the Default Gateway, the display will return to Static
IP. When you are finished entering the network information, press exit to save settings and exit again to
exit out of programming mode.
MLAN commands use TCP port 9999 (G2, OPC, MLAN).
WSB COMMUNICATIONS
– Sets the Blender ID number
Press (*,6,6) to enter an identification number for this particular weigh scale blender. This I.D. number will
appear on all printed reports. If you have more than one unit, this helps to identify reports. If you are using
a computer to automatically gather data, then each controller must have a unique address. Valid numbers
are 000 to 255. When connected to a computer, do not use the number 000 for identification. When
finished, press
Exit to save changes, then press Exit again to exit out of Programming Mode.
MODBUS COMMUNICATIONS
– Enable / Disable
Press (*,6,7) to enable or disable Modbus communications.
Press "*" to toggle between ENABLED
and DISABLED .
Press Exit when complete. Modbus commands use TCP port 502 . Modbus
registers are available upon request or may be downloaded from our website.
Regrind hopper as second natural
Press (*,6,9) to set flag to treat the "REGRIND" dispense as a SECOND NATURAL material.
With the flag
DISABLED , Natural is calculated to fill the space remaining in the weigh bin after a Regrind
dispense has occurred. In other words, when a reduced amount of Regrind is dispensed, additional
Natural is dispensed. Color and Additive dispenses are calculated as a percentage of this Natural
dispense ONLY.
With the flag
ENABLED , Natural is calculated to maintain the proper RATIO between the two components
(Natural and Regrind). Color and Additive dispenses are calculated to add to BOTH components at the
requested ratios.