Maguire Products WEIGH SCALE BLENDER WSBMB Series, Установка, эксплуатация и обслуживание

Страница: 97 / 148

M A G U I R E P R O D U C T S , I N C .
97
W E I G H S C A L E B L E N D E R

Interpreting the *54 Cycle Printout
10 or 20 cycles of data can tell a lot about the performance of your blender. The following will help you interpret the
data. This example uses the data from a 12-12 controller.
A single cycle printout looks like this: (dashes ---- added for clarity of spacing)
----------- ------------ ------------ ------------ ------
**1 R20.0** **2 N 100** **3 A 04.0** **4 A 00.0** TOTAL
* 11/10/16 * *16:17:53 * RECIPE 0000 **ID# 051** **WO 00000* OPR000
FINAL: DISP,% 0.0 0.0 1908.3 77.6 4.06 0.0 .00 2000.1
RATE: GR/TIME 18224 976 19993 488 12973 31232 10240 31232 9.9
1 ST DISP,TIME 0.0 0.0 1908.3 469 77.6 1826 0.0 .00 22
DEFINITION OF EACH LINE
The
TOP-OF-PAGE heading:
----------- ------------ ------------ ------------ -----
**1R 20.0** **2 N 100** **3 A 04.0** **4 A 00.0** TOTAL
Prints as a heading to each page, or once every 10 cycles. This serves as a heading over four columns of material. Additional
lines will print for additional components as necessary, printing only those components turned on. Thumbwheel setting and
material type is shown for each. If a thumbwheel setting is changed, a new header line will print.
In this example, component 1 is a REGRIND; component 2, a NATURAL; 3 and 4 are set up as ADDITIVES.
The
CYCLE heading:
* 11/10/16 * *16:17:53* RECIPE 0000 **ID# 051** **WO 00000* OPR000
DATE and TIME this blend cycle was completed. RECIPE, ID, Work Order, and Operator numbers have no bearing on blender
operation but aid in identifying this particular blender, and what job was running.
DATA LINE 1 :
FINAL: DISP,% 0.0 0.0 1908.3 77.6 4.06 0.0 .00 2000.1
For each material, each column shows the final dispensed weight of that material and its percentage of the blend.
In this example Natural dispensed 1908.3 grams. Color dispense is 77.6 grams, 4.06 percent of the natural dispense, slightly over
the 4 percent requested.
The final number, 2000.1 is the total weight of the blend. It equals the sum of the component dispenses.
DATA LINE 2 :
RATE: GR/TIME 18224 976 19993 488 12973 31232 10240 31232 9.9
These numbers show the RATE of dispense for each material. These are the numbers that the software used to calculate how
long to open the slide gate or run an auger, in order to dispense the required amount. This is GRAMS per (milliseconds in 4088
Standard controllers, and Interrupts (244/second) in 12-12 controllers); 1822.4 grams dispensed in 976 interrupts, which is 4
seconds.
The final number, 9.9 grams, is the TARE WEIGHT of the weigh bin displayed just before the cycle began.
DATA LINE 3 :
1 ST DISP,TIME 0.0 0.0 1908.3 469 77.6 1826 0.0 .00 22
This shows the first dispense in grams for each material and the timing of that dispense (in interrupts).
If the first dispense weight, (data line 3), matches the final dispense, (data line 1), then no "retries" occurred. In other words, the
software accepted the first try. If they do not match, then the first try was short and one or more retries occurred. The second
number is the dispense time that the software calculated to be a correct first try for the dispense.