Magnum MLT4060KV страница 15 Скачать руководство пользователя | Manualshive

Страница: 15 / 40

background image

15

RAISING THE MAST

1. Set up and level the unit. Refer to

“Light Tower Set

Up” on page 14

.

WARNING

The unit must be leveled with the

outriggers extended before raising the

mast. The outriggers must remain

extended while the mast is up. Failure

to level the unit or extend the

outriggers will severely reduce

stability and could allow the unit to tip

and fall.

2. Check the mast cables for excessive wear or dam-

age. Make sure the cables are properly centered in
each pulley (A). Check the electrical cord for damage.

WARNING

Do not start the unit if insulation on the

electrical cord is cut or worn through.
Bare wires in contact with the mast or

frame may energize the unit and cause

electrocution. Repair or replace a

damaged cord.

3. Press and hold the winch control toggle switch (B)

upward to telescope the mast to the desired height.
Extend the mast slowly, making sure that the coiled
electrical cord is extending at the top sections of the
mast. If, for any reason, the winch cable begins to
develop slack or any of the mast sections get stuck,

STOP IMMEDIATELY

and contact an authorized

service center.

CAUTION

Do not extend the mast beyond the

colored mark on top of the lower mast

section (C). A limit switch on the main mast

section will disconnect power to prevent

overextending the mast.

4. The mast can be rotated by loosening the mast rotation knob at the bottom of the mast (D). Turn the mast until

the lights face in the desired direction and then tighten the knob.

WARNING

Never raise or lower the mast while the unit is operating.

D

C

B

A

STOP

DETAIL C

DETAIL B

00183

«
...
13
14
15
16
17
...
»

Содержание MLT4060KV









































Отзывы:

Нет отзывов

Похожие инструкции для MLT4060KV

Бренд: MacDon Страницы: 89

Бренд: Yates Страницы: 2

GPSMAP 188 Sounder

Бренд: Garmin Страницы: 134

Бренд: IDEAL Networks Страницы: 10

Бренд: Qu-Bit Electronix Страницы: 15

Бренд: AMP Lighting Страницы: 5

Бренд: Strapack Страницы: 16

Бренд: Hameg Страницы: 60

Бренд: TaoTronics Страницы: 2

Бренд: PALAZZANI Страницы: 131

VEX-WPCR Series

Бренд: Exitronix Страницы: 4

ADVANTAGE 78400-117

Бренд: Medivators Страницы: 12

INTIMIDATOR 15XPC

Бренд: Bandit Страницы: 112

Бренд: ZAMST Страницы: 14

Бренд: Elliott Страницы: 46

Бренд: KUHN Страницы: 44

BoilerMag XT Series

Бренд: Spear & Jackson Страницы: 8

Бренд: MAHA Страницы: 138

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды