Magnum MLT4060KV страница 28 Скачать руководство пользователя | Manualshive

Страница: 28 / 40

background image

28

TOP-WIND MODELS

•

Apply a lightweight oil to the screw stem.

TRAILER WHEEL BEARINGS

The trailer axles are

equipped with a grease zerk fitting to allow lubrication of the wheel bearings without the need

to disassemble the axle hub. To lubricate the axle bearings, remove the small rubber plug on the grease cap, attach
a standard grease gun fitting to the grease zerk fitting and pump grease into the fitting until new grease is visible
around the nozzle of the grease gun. Use only a high quality grease made specifically for lubrication of wheel bearings.
Wipe any excess grease from the hub with a clean cloth and replace the rubber plug when finished. The minimum
recommended lubrication is every 12 months or 12,000 miles (19,312 km). More frequent lubrication may be required
under extremely dusty or damp operating conditions.

LOWER RADIATOR HOSE HEATER OPTION - USE AND MAINTENANCE

CAUTION

Improper use of the lower radiator hose heater could result in damage to the engine or

personal injury. Do not modify the location of the lower radiator hose heater.

The following points should be followed when operating a unit equipped with a lower radiator hose heater.

•

Ensure the cooling system is full of the proper mixture of water and engine coolant before each heater use.

•

The heater is designed for all-night operation, however, 2-5 hours of heating just prior to starting is usually
sufficient for proper engine starting.

•

The unit must be level to maintain proper orientation of the heater while it is in operation.

•

Use only an undamaged, outdoor rated, three-prong grounded 120VAC extension cord with a minimum
amperage rating of 10A. Connect the cord to a properly grounded 120VAC, GFCI receptacle.

•

Before starting the engine, unplug the extension cord from the power first, then unplug the heater cordset
from the extension cord.

Oil

Grease

Grease

Grease

Oil

Oil

Oil

Oil

00243

«
...
26
27
28
29
30
...
»

Содержание MLT4060KV









































Отзывы:

Нет отзывов

Похожие инструкции для MLT4060KV

Бренд: MacDon Страницы: 272

Бренд: MacDon Страницы: 70

MET ONE 3400 Series

Бренд: Hach Страницы: 48

Varycolor MICRO 150HTI

Бренд: JB-Lighting Страницы: 18

SC 2 Deluxe EasyFix

Бренд: Kärcher Страницы: 12

Бренд: Kärcher Страницы: 16

Smart Plus PHT-35LHS

Бренд: Vatech Страницы: 190

Бренд: York Страницы: 16

i.Profiler plus

Бренд: Zeiss Страницы: 66

Бренд: Valko Страницы: 10

Optima XR200amx

Бренд: GE Страницы: 46

Бренд: MadLab Страницы: 7

Бренд: Irwin Страницы: 2

Бренд: Carbatec Страницы: 29

Бренд: PurAthletics Страницы: 2

Бренд: Emos Страницы: 8

Бренд: Kärcher Страницы: 60

Бренд: ESD Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды