Magnum MLT4060KV страница 14 Скачать руководство пользователя | Manualshive

Страница: 14 / 40

background image

14

LIGHT TOWER SET UP

1. For maximum light coverage, locate the unit at ground level or in a spot higher than the area being illuminated

by the lamps.

WARNING

The mast extends up to 25 ft (7.6 m). Make sure area above the unit is open and clear

of overhead wires and obstructions.

2. Place the unit on firm ground that is relatively flat, then block the wheels to keep it from moving (A). This will

make it easier to level the unit.

3. Pull the locking pin on the tongue jack and rotate the jack 90°. Replace the locking pin (B). Turn the jack handle

clockwise to raise the trailer tongue off of the towing vehicle.

4. Connect a good earthen ground to the grounding stud on the frame of the trailer near the trailer tongue (C).

Note:

Consult local codes for proper grounding requirements.

5. Pull the locking pin (D) on the outrigger (E) and pull each outrigger out until the spring loaded locking pin snaps

back into place. Pull the locking pin on the outrigger jack and rotate each 90° so the jack pad is facing down and
the spring loaded pin snaps back into place.

6. Pull the locking pin on the rear jack (F) and rotate the jack 90° until the spring loaded pin snaps back into place.

Turn the jack handle clockwise to start leveling the trailer. Adjust all four jacks by turning their handles clockwise
until they are firmly in contact with the ground and the trailer is as level as possible (G).

7. Before raising the mast, it may be necessary to adjust the lamps. The lamps may be adjusted up, down, left or

right by loosening the wing nuts on the trunnion (H) and aiming them in the desired direction. Tighten the hardware
completely and make sure the lamps are connected to the junction box (J).

DETAIL C

DETAIL D

DETAIL G

DETAIL H

D

C

E

H

A

B

D

J

F

G

00156

«
...
12
13
14
15
16
...
»

Содержание MLT4060KV









































Отзывы:

Нет отзывов

Похожие инструкции для MLT4060KV

SATURA SPOT LED PRO

Бренд: Elation Страницы: 41

Бренд: Tapco Страницы: 16

Бренд: Zenbooth Страницы: 40

Visium CytAssist

Бренд: 10x Genomics Страницы: 51

Chromium X Series

Бренд: 10x Genomics Страницы: 5

Бренд: Danfoss Страницы: 106

Бренд: xsto Страницы: 76

Бренд: F&V Страницы: 5

Бренд: F Care Systems Страницы: 2

Pressure Governor

Бренд: Waterous Страницы: 53

Бренд: Landi Renzo Страницы: 16

Бренд: IBM Страницы: 163

Бренд: Toro Страницы: 4

Бренд: LSI Страницы: 24

TOBIAS W775A03BKG

Бренд: Home Decorators Collection Страницы: 14

Бренд: DC Med Страницы: 2

Бренд: Erbe Страницы: 154

TRACER pH PockeTester 1741

Бренд: LaMotte Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды