background image

 

37

 

 

 

 

Your 

MagnuM Biomass Pellet Stove

 comes to you with the glass door installed in place, ready for use.  

The glass is surrounded on the edges with a gasket and seated in a glass channel.  It is held in place with 
two (2) clips on the top and two (2) clips on the bottom and two (2) clips on each side. 

REMOVAL OF BROKEN OR DAMAGED GLASS 

Open the door and lift it off of hinges.  If the door is tight, tap gently on the bottom of the door with your 
hand or rubber hammer.  Lay door on newspaper with glass clips facing you.  Using a #2 Phillips 
screwdriver, loosen the screws and take the glass clips off.  Remove the broken glass carefully and 
discard. Check to insure that the gasket material under the glass is in working order. You can obtain this 
material from the factory or from an authorized 

MagnuM

 reseller if it is in need of replacement. 

Reverse the above procedure for replacing the new glass.  

When installing the new glass insure that the 

glass is not sitting on top of any obstructions.  The glass will break when tightening the screws if the 
glass is on the gasket.  Hold the glass toward the top of the door glass channel when tightening. 

 

 

 

 

 

 

 

 

 

CLEANING THE GLASS 

When the fire is first started, it will produce some smoke.  The smoke might accumulate on the glass 
surface.  Before the fire gets hot, open the door and wipe the glass surface off with a damp rag.  Do not 
touch the surface with your hands.  If after constant use, the glass is dirty; you must clean the glass so that 
it will not become etched with the fly-ash.  When the glass has cooled off, take a damp rag, put a little fly 
ash from the unit on it and clean the glass.  If this does not clean the glass use a special glass cleaner 
provided by your 

MagnuM 

reseller.  

We have found that Amway’s Crème Glass & Chrome Cleaner 

works 

very well. 

 

 

 

 

 

 

 

 

 

 

GLASS MAINTENANCE, ADJUSTMENT, REMOVAL AND REPLACEMENT 

WARNING 

 

Do no operate unit with broken glass. 

Do not substitute original factory glass. 

You must use only factory authorized glass: 

Do not slam door shut. 

Do not strike glass. 

Do not use abrasive cleaners. 

Do not clean when glass is hot. 

Содержание Elite WIN-ACI


















































Отзывы: