background image

 

8

 
 
 

When you receive your MagnuM Corn/Biomass/Wood Pellet Stove

, Pedestal unit, Leg unit or 

Fireplace Insert

, be careful to inspect all parts and components to make sure that nothing was 

damaged or lost in shipment.  If there was shipping damage, be sure to report it to your MagnuM 
reseller, or the shipping company that delivered your unit.  

Freight damage claims must be made to 

the Freight Company immediately.

  If parts are missing contact your local MagnuM reseller or 

contact the factory right away.  

Your satisfaction is our top priority

 
To uncrate your 

MagnuM appliance

 

1)

 

Cut the banding straps and open the carton lid. The carton is stapled to the wood pallet so it will be 
necessary to pull the cardboard loose from the pallet. Remove the crating box carefully lifting up over 
the top of the unit. Be careful not to scratch the unit with the staples. Remove the wood blocks and 
plastic. We strongly urge you to recycle the packaging materials to help protect the environment. 
 

The Pedestal unit comes completely assembled, the Insert comes with the shroud packaged separately and 
the Leg unit comes with the legs packaged in the hopper. 
 
The installation of the Insert shroud is shown later in the installation manual. Make sure that the shroud is 
with the unit when you get it.   
 
The following diagram will show how to install the legs on the Leg Unit. The legs are wrapped up and 
packaged in the hopper.  Unpack the legs and get the four (4) nuts out of the hardware bag. 
 
Tip the unit back so that you can get the leg onto the bolt that is sticking down in each corner of the 
bottom of the base.  Be sure to have someone helping hold the unit while you are attaching the leg.  The 
casting could break if bound or dropped.  
 

NOTE: It is best to attach the legs on one side first and then lift the unit up level to attach the other 
side.  You can also attach the legs on the back two corners first and then the front. 

 
Place the ¼” nut on the bolt that is located on the base of the unit and attach the leg to the bolt.  Swing the 
leg so that the foot of the leg is parallel with the 45-deg. angle of the front of the unit.  Align the back leg 
to match the front leg. 
 
Be careful not to bind the leg when bolting onto the unit so that it does not break.  The legs are designed 
to face at a 45 degree angle so that they will face in the same direction as the slanted side of the face. 
 
When the legs are bolted on and positioned where you like them, tighten the four (4) nuts.  Make sure not 
to over tighten the nuts and twist them off. 
 
 
 
 
 
 
 
 

UNPACKING YOUR MAGNUM CORN/BIOMASS/WOOD PELLET UNIT

 

Содержание Elite WIN-ACI


















































Отзывы: