manualshive.com logo in svg

Magnum Energy ME-MR Series, Руководство пользователя

Поделиться
Скачать
Magnum Energy ME-MR Series Скачать руководство пользователя страница 23

©2009 Magnum Energy Inc. 

21

Operation

5.2 Operating the Inverter/Charger

Turning the inverter on:

 Press the ON/OFF pushbutton to activate the in-

verter function. The inverter will either be actively inverting by using power 

from the batteries to power the AC loads (see 

fi

 gure 5-4); or will be searching 

for a load by using very little power from the batteries - if in search mode 

(see 

fi

 gure 5-3). The green ‘INV’ LED will be on when the inverter is actively 

inverting and the green ‘INV’ LED will 

fl

 ash while searching.

Turning the inverter off:

 While the inverter is actively inverting or search-

ing, the ON/OFF INVERTER pushbutton can be pressed to switch the inverter 

function off and this will turn the green ‘INV’ LED off (see 

fi

 gure 5-2).

Inverter Standby:

 The inverter is in standby when the inverter is active 

(green ‘INV’ LED is on) and an external AC power (utility/shore or generator) is 

passing through the inverter to power the AC loads. During normal operation, 

the AC loads will be powered by the external AC power, however, if a blackout 

or brownout condition occurs, the inverter senses these conditions, transfers 

to inverter mode and powers the AC loads connected to the inverter.

CAUTION:

 If you have critical loads and in Inverter Standby, do not 

press the ON/OFF pushbutton to turn the inverter function off. If the 

green ‘INV’ LED is off, inverter power will NOT be available to run 

your critical loads if the external AC power is interrupted.

Equalize charging:

 Equalizing is a controlled-overcharge performed after the 

batteries have been fully charged. It helps to mix the battery electrolyte (to 

reverse strati

fi

 cation) and also helps to remove sulfation that may have built 

up on the plates. These conditions, if left unchecked will reduce the overall 

capacity of the battery.

WARNING:

 Do not perform an equalization charge without reading 

and following all safety precautions pertaining to charging/equaliza-

tion as noted in this manual and any equalization information in the 

inverter’s manual.

To enable the equalization charge; see 

fi

 gure 5-10 and follow all related 

information on page 25.

5.3 System Status Messages

The remote control uses the top line of the LCD display to show the inverter/

chargers operation by displaying a status message. This section will show 

the inverter/charger’s operating modes and the available status messages 

under each mode. Use these status messages along with the Status LED’s 

to determine the inverter/charger’s current operating status and to help 

troubleshoot the system if a fault occurs.

There are three operating modes of the inverter/charger:

• Inverter Mode         • Charger Mode       • Fault Mode

Содержание ME-MR Series









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды