IMPULSE•VG+ Series 3 Instruction Manual – 07/25/05
5-70
Digital Outputs—Alarm/Fault Annunciate (H2-01~03=40)
Digital Outputs—Fault Annunciate
enables you to assign a set of six fault outputs to Relay Output
M3/M4 and/or Output M5/M6. In addition, you can select whether each fault output is enabled.
NOTE:
Output M1/M2 can also be used for
Digital Outputs—Fault Annunciate
; however, it is
normally assigned to a brake output.
Before you start to program this feature, you may find it convenient to first photocopy the “Binary-
to-Hexadecimal Conversion Worksheet” in this section. By being able to write in the worksheet’s
boxes, you will find it easier to program the feature.
Programming
Digital Outputs—Fault Annunciate
requires that you determine two 4-digit binary
numbers and then convert these numbers to two 1-digit hexadecimal numbers. You enter the
hexadecimal numbers when you program the drive.
To program
Digital Outputs—Fault Annunciate
(assuming you are in
Programming Mode
):
1. Press the
UP
button until
appears.
2. Determine the output terminal to which you want
Fault Annunciate
assigned; Terminals M1-
M2, M3-M4 or M5-M6.
3. Press the
button. “01” blinks. Press the
UP
arrow
button to select Relay Outputs 2 or 3.
4. Press the
DATA/ENTER
button.
5. Press the
UP
or
DOWN
button until
appears.
6. Press the
DATA/ENTER
button.
appears.
7. From the following worksheet, select one of three fault output sets. (Each row is a set.)
Enter the one-zero combination that corresponds to the set (row) that you selected.
For example, if you selected Set 2, you would enter “1 0” in the first two columns from the left,
which would represent the first two digits of the first binary number that you would convert later.
Digital Outputs
H2-01=0
TERM M1-M2 SEL
>
H2-XX=40
Fault Annunciate
Fault Data Input
OF
Table 5-6:Binary-to-Hexadecimal Conversion Worksheet
First digit from the left
Second digit from the left
Set 1
0
1
BE8
BE6
BE5
BE3
BE2
BE1
Set 2
1
0
OT1
OT2
LL1
LL2
UL1
UL2
Set 3
1
1
SLC
BE4
BE3
BE2
BE1
BE0
1 or 0
1 or 0
1 or 0
1 or 0
1 or 0
1 or 0
1 or 0
1 or 0
Содержание IMPULSE VG+ Series 3
